Viewing all customer Discussions for:

81-023 Sliding Door Roller, 1-1/4"dia. Steel Concave BB

I'm having a hard time finding a match for two rollers: Roller stamped A-S NYC 7867 3 5/8" long 1 3/8" tall 3/4" wide The roller is stuck inside, but the OD is appears to be 1 1/4" The brass roller has no stamps 2 1/2" long 1 1/4" tall A little over 5/8" wide OD wheel 1 1/4" Additionally, I canno ... (cont.)

I'm having a hard time finding a match for two rollers: Roller stamped A-S NYC 7867 3 5/8" long 1 3/8" tall 3/4" wide The timer is stuck inside, but the OD is roughly 1 1/4" The brass roller has no stamps 2 1/2" long 1 1/4" tall A little over 5/8" wide OD wheel 1 1/4" Additionally, I cannot find ... (cont.)

Hi I was hoping someone can help me find replacement wheels for attached picture. Top of bracket reads "ASTRCBEC OMCO" Thanks Matt

We need 2 of these single 1 1/4 inch rollers. The door is 44 years old and on our boat.Thank you!John

I'll use the following terminology: vertical frame member, horizontal frame member, 4-sided bracket, 3-sided bracket, roller axle. I'm trying to describe the door in a way that makes my terminology clear. The door has a vertical frame member that runs the height of the door that seals to the glass. ... (cont.)

I am looking for replacement rollers for an Alenco sliding glass door since one roller has completely failed (roller fell off). The door handle assembly is a secondary concern since it still functions and could be replaced later. The broken roller assembly is shown in two of the uploaded pictures. ... (cont.)

Home built circa 2004, sliding patio door rollers are broken brand name says ultra but I can't find them anywhere.

Help :)

I have been searching for replacement rollers for my patio sliding door on my mobile home which was built on 1996. I am sure due to the age of the door and the building the marking, numbers and name of the door has been worn away. If you can help me out, I would greatly appreciate it. I need (2) rol ... (cont.)

Hi, My name is Luis. I would like to know if you carry the part of the pictures I uploaded. I believe my sister needs five. Thank you for your attention in this matter. Luis

I have measurements that seem like this part is the right one. I believe it is Patio Roller Assembly, 1-1/4" Steel Ball Bearing Part # 81-279 I am sure on the 1 1/4" metal roller 2.5: case (which shows 2.58 in your drawing and I could be off that much)and the 1 3/8" height. Just checking for your ... (cont.)

I need assistance in finding this part Please. I would need 2 pairs of these. Thank you.

Do you have anything to replace these

Hi there. My mid-50s slider is suffering and in need of new wheels. I've searched the internet for photos of the same wheels, but no luck. The one identifying name is on the inside, but it's missing some letters so I'm not sure what the word actually is. The height adjustment on this door has to ... (cont.)

I had to pry out the roller the device was being held inside the door frame by a screw mounted in the frame ( see top of roller part)

W 3/4" H 1-1/8" Steel wheel 1-7/16" Unlike all the YouTube videos, these where held in place by a screw through the removed bottom piece. FWIW, this is on a mid 90's mobile home patio door. Need replacement as soon as I can find them.

These are from a patio door manufactured in the mid 1980s

My name is Larry and I am having a hard time finding the part I know that it is no longer made so I need to know what the replacement part number is

Jordan S-50/51 sliding glass door replacement roller assembly Roller bearings are worn out. Outside diameter of rollers is 1 1/4". I'd like to replace the entire roller assembly. I've looked through many pictures of roller assemblies without any luck finding one that looks like mine. ... (cont.)

I would like to replace my patio door rollers, they are at least 20 years old at barely work; the only marking on them is "Production Enterprises Hialeah, FLA"; your site had so many options, I wasn't sure which were the correct ones; let me know if you need more information