Viewing all customer Discussions for:

81-027 Sliding Door Roller Assembly, 1-1/4" Concave BB Wheel

The condo complex was built in the 70's replacement glass size for the patio sliding door is 46"X76" (5/8"thick) Roller Dimensions are 3/4" thick, 2"long, 1"tall wheel size is 1&1/4"

There are no markings on this roller. or door.... Give me your best guess please

Rollers on my glass slider went there single wheel with the adjustment screw at the bottom and a set screw above the aama certification program says it is an sgd-c30 mst:15068 series 9000 aama 101-88 mfgr code yo-1 . What is the replacement #

This condo was built in approx. 1965 and we believe these doors are original. Approx. 8 ft. metal patio doors that meet in the middle with two stationary doors at either end. Extremely expensive to replace and no one knows who the manufacturer is.The right hand door has been used forever and just ab ... (cont.)

Hi,I am trying to find the correct lock for a sliding patio door for my daughter's Condo in Somerset, N.J. It appears as though the current lock & keeper combination was done "after the fact" but I can't tell for certain. I recently installed your part 81-027 roller assembly in this door and it ... (cont.)

Hi. Please help me and then defy part number

There is one nylon wheel with a groove in the middle and the wheel is 1 1/4", the height is 1", the length is 2 1/8" and the width is 5/8" (not counting the slight bump outs on the side).

HI - I am looking for a replacement roller for an Acorn Sliding Glass door. The wheel measures 1 1/8", the frame is 2.5" long and 1" height.

Please help me identify this part...thanks

1970s installation

I forgot to measure the wheel. If it is very important I'll pull the panel again and measure the wheel.I believe the slider is from 1982 when the condos were built. But can't find any brand name.I'm hoping to put 2 tandem sets in to make it easier to slide. Any advise would be great.Thx Kevin ... (cont.)

acorn dorwal sliding double pane glass door h 72"x w 36 3/4" x 1 " thick. roller assembly : L 1 3/4" X H 1" {not including the roller), W OF CASING ABT 1/2" (or tick less on screw end ) diameter of roller 1 1/4" marking on casing is D-719 .It might be your part number 81-027 according to Bruce in ... (cont.)

My internal single glazed aluminium double sliding doors are approx. 35 -40 years old ... still in good condition but require rollers and tracking replaced. Problem identifying and finding such here in UK, can you help?Approx. Roller diam. is 1 7/16" x 5/16" wide. Length of casing 2 9/16" x 1 1/2" h ... (cont.)

I need 4 roller assembly for Jen Weld aluminum patio door. Can you help?

There is a number on the side I believe is D170 or D179. I have searched and can't find a exact match. There is a piece that this piece fits into that mounts the assembly mounts to. Unfortunately I dont that piece in my hand. Please recommendations

I need this roller assembly #81-027 with a 1-1/8 wheel.Looking at a possible substitute # 81-125 and #81-263 #81-125 and cutting the clips off the top.Can I special order #81-027 With 1-1/8 wheel? I have 24 of these doors most with bad rollersThanks Ken

hello, I was looking through rollers and wanted to make sure I was picking the correct ones. I think its the Product Code: 81-027 but I'm not 100%. Thankyou

I need to replace the rollers on my sliding door. This door was the original that came with the house built in 1970. It has a sliding door and stationary door. Total width is 6', sliding door is 3'. I can't find anything on the door itself that identifies a part number. The door handle has the c ... (cont.)

Looking for this part

I need to replace the rollers on my 32-year-old Acorn sliding glass door. I've attached a partial scan of the installation instructions that give the series of the door as "DorWAL Insul-DOR SERIES 800"; panel 6A identifies it as Roller assy PN 8001 and the sketch on panel 7 may help in identifying ... (cont.)