Viewing all customer Discussions for:

81-033 Sliding Door Roller, 1-1/4" Steel Ball Bearing

I have a 10 foot acorn doorwall installed around 1970. Which rollers do I need for the sliding door?

Could you be kind and confirm replacement Patio wheel assembly on the following attached pictures. I believe is Acorn Patio sliding glass door, I no longer can adjust, adjustment screws are shot.SincerelyMario

I have an Acorn Patio slider that needs new rollers. The door is located at a beach house on Fire Island. The door is 48" wide and 96" tall. Would you know which rollers are needed for this door. It is a double pane door Thanks Mike

Which roller do I need? I am on the Homeowners Association for a condominium in Seattle and we have ~50 doors where rollers and some handles need replacements. We are fine doing one door to verify parts if you suggest we order an assortment of roller pairs and see which ones work. Thanks ... (cont.)

Could use some help Identifying the roller hardware in the bottom of the door. Also any suggestions on who may have done the 3 session room install. If they are still in business I would hire them to restore all the rollers and seals.

Need new rollers for my Acorn sliding door, no numbers on main frame,, door in place , so don't have roller photo, door is approx 20 years old. HELP

I have two sliding doors one is 48" X 78" and one is 36" X 78". They are Acorn doors I need to replace the rolls on them,but I have no idea the replacement parts to order can you please help me. Thanks; Judi

Identifying marks on roller: del mar eng Long Beach, CA Pat. # 3.670.357 Dimensions: 2-1/2" long x 2" tall x 3/4" wide roller is stamped "Kilian" Syracuse Toronto attachment piece is verticle w a 3/16" hole

Need 2dorwal patio door rollers.

The rollers for this old sliding door (about 1985) are still working, but not well. Tonight I removed them to take a photo, and then put them back in the door. They don't have a manufacturer name or part number. There is one set at each end of the bottom of the door. I got a similar set ... (cont.)

sorry about poor photo quality; I am pretty sure these are the Sliding Door Roller, 1-1/4" Steel Ball Bearing Product Code: 81-033 stamped on side - Del Mar Eng CO. wheel size- 1 1/4"; 1 1/8" tall; 3/4" wide; 1 3/4" long single wheel at each frame end.. thanks for the help

I have a Acorn/Doorwal door that needs the rollers replaced and can't seem to locate them. Can you give me all your part numbers that are applicable?

Here are the pictures I could not find a serial number, but the house was built in 1990 if that helps. I need the inside door handle, and rollers.

We are looking to order 30 sliding door replacement wheels.picture is attached it was made by Del Mar Engineering and has a pat stamp of 3670357. It is aprox 1 1/4" wide (not including the wheel) and 2 1/2" high including the wheel your help would be greatly appreciated Paul DEL MAR ENG. ... (cont.)

Hello I WORK IN A HOSPITAL IN THE I.C.U WARD AND WE HAVE A SLIDING GLASS DOOR FOUND SOME PAPER WORK FOR IT SAYS IT,S A AMARLITE " METROPOLITAN MARK II " ARCADIA SERIES 800 " OR PITTSBURGH PLATE GLASS CO "PITCO GIANT " CAN YOU ID THIS ROLLER FOR ME THANTS

I'm trying to find rollers to replace the rollers on my patio door. I looked every roller on your site and didn't see anything that looked exactly like the ones on my door. Attached are a couple of pictures ot the rollers from the door. Any chance you could identify these and let me know wha ... (cont.)

i can drill out the old one. do you have a replacement?

Hi guys, I'm looking forward to get the replacement parts for these items : 2 rollers and a (lock) handle. Pictures submitted in 2 separate emails. Please, help me identify them. Thanks for your time, Francois

I have replaced the wheels on my 4'door (8' doorwall) 3 times now. The adjustment screw pushes out on one side only. I have installed nuts inside (even an acorn nut on the inside end of the adjuster) but the 3/4" wide case collapses... the door is very heavy. Do you have a heavy duty model wheel ... (cont.)

We believe our part 81-033 will work for you. It isn't die cast, but stamped steel. This roller was used by Acorn, Wells Aluminum, and Rollyson.