Viewing all customer Discussions for:

81-090 Sliding Door Roller, Concave

I am looking to replace sliding door assembly. Please look at the attached photos of the broken part and let me know the matching part number. Thanks, Zoran

Please provide dimensions for your 81-090

I have attached 5 pictures that I hope will help you identify the correct replacement sliding glass door rollers. Each picture has a ruler included in the picture to help you with the size of the unit. The wheel is one inch in diameter. The body is stamped "PRODUCTION ENT" on one line and " ... (cont.)

Rollers adjusters for sliding patio doors

Looking for these rollers

I placed an order for replacement, but now I want to make sure I'm getting the right part. Pulley outside diameter: 1.16" Pulley diameter at bottom of V-grove: 0.84" Thickness: 0.55 (but it's hard to tell because it's so rusty). Without rust it might be 1/2" What do you recommend, based on thes ... (cont.)

Hi, we placed an order for replacement patio roller, item number 81-011. We measured and found this item to match what we have but never noticed it had flat wheels. We need concave wheels. Is there a different item number for this housing unit with concave wheels? At this point, the door will not op ... (cont.)

Need to replace roller hardware or obtain wheels of similar size to be installed an existing hardware

The Aluminum Channel Dimensions: Outside Width - 5/8" Inside Width - 1/2" Inside Height - 1 1/8" The Assembly slides into the channel. The Assembly Dimensions: Width - 1/2" Height - 1 1/32" Length - 1 7/8" Wheel Diameter: 2 1/4" Markings: Production Ent #6232

Hi there really hope you can help me out. I need to purchase this roller but can't seem to find it anywhere. Please let me know how much it would cost. I hope the pics & drawing help identify it... the only marking is 138-R. Great site BTW Regards, Joe

bought doors without rollers see picture of one. need 6 have 2 thank you

Is this product available in stainless steel or brass? This is for a marine saltwater application 81-090 Do you also have parts like the attaced images? The part with concave roller is about 7/8" w x 3/8" d x 1 15/16" tall and the roller is 7/8" in diameter. And the other smaller roller is ab ... (cont.)

I need some help to determine a actual roller. The closest thing I saw was the 81-090 not exact but appears to be close.

I just ordered some sliding door rollers pt# 81-090. however looking at the picture I could not tell the size (width) I ordered anyway hoping they would fit but they didn't. I require a width of 3/4 inch. do you have anything like that?

After much difficulty searching for the correct replacement rollers for my patio sliding door, I believe your model 81-090 is the closest I have found. My units have the number 138 stamped on the side, but I don't know if that is a properly definable number. The measured size matches perfectly exc ... (cont.)

I am looking for replacement parts for an aluminum sliding door. The house was built about 15 yrs ago. The door is a three panel door with center slider. 9 foot wide by 8 high. the aluminum track at the bottom of the door is smashed down, It is a double track style, with each track about 1/8 wide wi ... (cont.)

I'm seeking to replace the two bottom assemblies/rollers in a marine sliding door application. I believe the original item is a PE Delmar, SF1. It has a 1.25" dia nylon wheel, length 1.92", height 1.04 width .052 Can you help?

This is a picture of my old roller assembly. The concave roller size is 1

I believe I found the correct replacement glass door rollers(81-090)to replace my broken rollers. My question is can these type of rollers be pulled out from the bottom of the door without removing the bottom frame from the glass? They do not look to be held in by any other hardware, just look ... (cont.)

I need some replacement rollers for the Rolling patio Door for my porch enclosure. Dimensions are 2" wide x 1" Tall x 7/16" thick. Roller size is 1-1/8" Is this something you can provide?