Viewing all customer Discussions for:

88-002 Wood Pull, Hourglass Shaped, 6-5/8"

Door Series 2000/930. The numbers on the hardware are too corroded to read. Hopefully you can help. There are not holes to attach a handle to the door, but a rectangular cut in the aluminum measuring approx. 5/8" X 67/8". The hardware fit into this groove and attached to the outside groove plate ... (cont.)

I would like to add a key lock assembly to this door. Do you have one that will fit this door? As you can see it is an inch wide and the locking mechanism is for one hole only.

would like to replace bracket (black) that holds handle. Thanks, fabian

No luck using your online post form. Here it is by email. I'm looking for a replacement latch with handles inside and out, preferably. The existing unit had a handle inside, which broke. The only ID we could find on the door was on the rollers, Allen Stevens 6047. The handle mounting ho ... (cont.)

We just purchased an older home constructed in the early 80's that has three sliding glass doors. The locking mechanism is broken on one and we would like to replace all three. Hopefully the attached pictures help. I found a mfg label that I can still read what looks like: - Code 172-1 - Se ... (cont.)

Hi my name is John: We have older patio sliding door. The handle is ( Daryl patio rama 300 ) Part #19058 and 19103-BL. Is there a such part or replacement for this item please let me know. John

Can you please help me to replace two handles on two doors? I am including photos of the handles. Thanks, Amy

I am looking to replace some sliding door pulls. The one I took apart has the following pieces: DNS Industries 12 Inside Pull Standard DNS Industries 13,23 Outside Pull Standard The screws are 6.5 inches apart. My current handle is 9 1/2 inches. What do you have available for replacement? I hav ... (cont.)

PART # 45FL02 is stamped on the inside. I have no make or model of window. Latch is 7 5/16 in length & 6 5/8 from bolt to bolt & 7/8 wide. This could be 10 years old or so.

DNS Industries 11 Inside Pull 1400 Series Hi, I am in need of sliding door lock replacement. It is manufactured by DNS Industries Miami. Total height of the lock is & 3/8". To best of my search they are 11 inside pull 1400 series. Inscription on it is ; 12 inside pull standard 11 out ... (cont.)

I am in need of a replacement sliding door handle for a Pella door. We recently purchased our house and serial number on door is not visible. The locking mechanism is separate and does not need replaced. Basically just need a pull handle. The distance between the screws is approximately 7". Please l ... (cont.)

I have lost the key and need to replace this handle with another that is similar. The Dimensions are (Length 7 5/8" withe 15/16

Weather strip on glass.

I need an interior handle (only) for a sliding glass door. The locking mechanism is separate not part of the handle. The lock is intact and working. These sliding glass doors were installed in 1971 and this if the first problem I have had with handles. I have photographed and measured the handle as ... (cont.)

written on door pulls---DNS Industries 13/23 Outside Pull Standard and DNS Industries 16 Inside Pull Standard. Please let me know prices of pulls and locks. thank you.

Looking for a replacement of this lock

Hello, Need to replace this item. dns industries 16 inside pull standard Thanks, if you can help me out. Leonard

Hello there, Please can you help a "limey" in distress. I am looking to replace a sliding door handle and I believe that it is the same as the one shown above. The 2 handles are inscribed as follows: DNS Industries 13/23 outside pull - standard. Miami, Flo., and 16 inside pull. I have watched yo ... (cont.)

Patio door handle set

I have taken a few pictures which I hope may help your research folks to find a best match. As you see, the name on the original lock set is CROWN. The hole/opening in the door when this lockset is removed (see photo) measures 2 cm x 18 cm.