Viewing all customer Discussions for:

88-002 Wood Pull, Hourglass Shaped, 6-5/8"

Screw to screw is 6 5/8 inches as close as I can tell, Also, I have other doors with same latch assembly that I need to have replacement handles with brackets. Thank you.

Do you have a product that will lock (from the outside) my sliding glass patio door? The dimensions are: Stile 1 6/8 in Inside door width 1 inch I have not been able to find anything that fits. There is no label on the door so I am unable to determine the manufacturer.

Can the 88-002 wooden door handle be used with the 82-002 patio sliding door handle?

I need the sliding 6 5/8" patio door handle replacement with a wood pull handle. I just see the metal piece, not the wood handle. Is that available? Thanks, Diane

looking to replace as thread in holes are stripped. I'm trying multiple submissions as it failed if I put in 5 pictures. Thanks Jim

I am looking for a door handle to fit this unknown manufacture door. the sketching on the glass sliding door looks like to be the following: Gaurdian Webster, MaSS ANSI-Z 971-1984 SAFE TEMPERARED LOOKS LIKE SOCO 300 1/8U WMH 3993 18-CFR OR COULD BE OFR -120111 Between the glass there ... (cont.)

I have a 7 1/4" by 1" latch which is on a 1" thick door. I need two for replacement. Can you guys help me?

The handle for my outside sliding glass patio door broke and it is marked DNS 5/25 outside door pull standard. Do you have it in stock or know where I can purchase it from? Thanks! Shelley

Hi! Trying to find a replacement for this handle.

I think I have this lock at my sliding door (see pictures) and its not working now. Actually the grapping hook is not working. (1) Is there any other lock for the same opening with stronger grapping arrangement? I don't need the lock but want stronger grapping?

Installed in 1984. The latch parts on the left and right doors were removed in order to install a dog door panel. Then they were lost.

Main locking slide (cast Al presumably) broke. House was built in 1989, original door and lock. Door is 6' wide Aluminum that is 1" thick. Opening in slider is rectangular approximately 7 1/8" L x 3/4" W. Pictures are of lock installed and removed. Dimensions between center of screw to center of scr ... (cont.)

There is no information that I could find anywhere on the door. The inside locking mechanism is broken; won't lock onto the catch that's on the door frame. Anyway of matching this up, or know where I can purchase a replacement? Thanks! Angie

Hello Swisco Crew! Pete Rose here from Home Hero Handyman Service in Philly. Good friend of the infamous Mr. Paul Pallas. Hoping your team can help me figure out a replacement handle for the above referenced patio slider. Total length top to bottom is about 7.25" LMK if you can help me ... (cont.)

DNS Industries, Miami, FL Chrome, hole centerlines = 6-1/2", keyhole centerline from top of exterior plate is 4-1/2". Inside lock handle has 12 INSIDE PULL JAPAN. Also has a raised numeral 2about 3-5/8" from the bottom The inside door pull has a 'Cherry' color wood handle (1-1/8"x9"x7/16") mount ... (cont.)

I am looking for a replacement lock/pull for my sliding door. Markings on the existing parts follows: DNS INDUSTRIES.11 OUTSIDE PULL MIAMI FLA. -1400 SERIES DNS INDUSTRIES.12 INSIDE PULL MIAMI FLA. -1400 SERIES Please advise if these are available. Thank you. Mike W.

I looked through your website but was unable to find my hardware from the pictures. My patio door is about 20 years old. The opening in the metal door is 1" x 7.25". The opening is cut through both sides of the door and is located 5/8" from the edge of the door. I have attached several picture ... (cont.)

I am looking for a replacement lock mechanism for my sliding glass door which were probably installed about 1957. They were made by Metal Industries Type SGD Class B1 Model # UB01121 (the B might be an 8) and Series M11. The distance between the screw holes is 6-5/8". There is a push up/down ope ... (cont.)

The lock to our sliding glass door is broken and we cannot seem to repair it anymore. Is this one too small for the hole? Please help!

DNS INDUSTRIES 13/23 OUTSIDE PULL, -1400 SERIES AND 01 INSIDE PULL