Viewing all customer Discussions for:

88-002 Wood Pull, Hourglass Shaped, 6-5/8"

Lock does not work. Door manufacturer not known. Home is in a retirement community-Holiday City, Toms River, NJ circa mid-70s. Looking for either lock mechanism or handle/lock. 2 Pix -including one to indicate measurement. As best we can, 7-1/4 from top to bottom of metal;6-5/8, 6-6/8from screw to s ... (cont.)

I've looked all over for replacement handle to no avail. Top part of Handle split vertical (duct tape covering in photo so handle is useable to get outside). Center-to-center hole of screws is 5 5/8" and 6" from bottom of bottom screw to top of top screw. Total height is 7 1/2" I have no idea whom o ... (cont.)

Hello,I would appreciate if you could assist locating the correct part. I would like to replace the existing locking mechanism with a lock & key without having to cut into the door frame. I was able to make out a marking on the glass door labelled V861 12GZThank you,Moussa

6 and five eighths inch screw spacing

Hi, please see attached photos of the existing lock. I would appreciate your help identifying the correct part to replace with a lock and key without having cut the door frame. Thanks!

do you have a patio door inside wood pull, hourglass shaped, 3 15/16"?

Only ident I can find on the lock is Delta Industrial Systems part number 45-8401

Please check my account for ordering this door pull 2 times 8-31-08 & 12-26-12 same product #88-005. If there is anything same size, let us know. My account is under Joan Hausfater using my email address Thank you so much for your help

I have two questions. I am looking at 82-002 to replace the broken lock on the patio door, but there are some differences. 1) Do you think it will fit? The measurements are perfect. 2) As you can see from the picture, the door handle/pull fits under the screws. Will I be able to attach the current ... (cont.)

Hi I need to replace a non-key door lock on a sliding glass patio door. 71/2" long & 1" thick frame. Black. I need the lock & catch on the frtame.

I have an Alenco 3 panel patio door. Each panel is 34x91. The lock mechanism is the standard one sold ta Lowe?s and Home Depot and it is a touch too small. The screws see to be about 6 5/8? apart. There is a bit of open space at the top of the opening in in the door and the hook, despite trying all ... (cont.)

15/16" WIDE - 7 3/8" LONG - 6 1/2" SCREW HOLE CENTER

Need two new recessed patio door handles and hopefully new wheels. This home is in Laughlin NV and was built in the 80?s

Does door handle 88-002 fit with door mechanism 82-008? Thanks.

Screw to screw is 6 5/8 inches as close as I can tell, Also, I have other doors with same latch assembly that I need to have replacement handles with brackets. Thank you.

Do you have a product that will lock (from the outside) my sliding glass patio door? The dimensions are: Stile 1 6/8 in Inside door width 1 inch I have not been able to find anything that fits. There is no label on the door so I am unable to determine the manufacturer.

Can the 88-002 wooden door handle be used with the 82-002 patio sliding door handle?

I need the sliding 6 5/8" patio door handle replacement with a wood pull handle. I just see the metal piece, not the wood handle. Is that available? Thanks, Diane

looking to replace as thread in holes are stripped. I'm trying multiple submissions as it failed if I put in 5 pictures. Thanks Jim

I am looking for a door handle to fit this unknown manufacture door. the sketching on the glass sliding door looks like to be the following: Gaurdian Webster, MaSS ANSI-Z 971-1984 SAFE TEMPERARED LOOKS LIKE SOCO 300 1/8U WMH 3993 18-CFR OR COULD BE OFR -120111 Between the glass there ... (cont.)