Viewing all customer Discussions for:

89-021 Steel Keeper

please see the picture. All on the pictures are OK. I just need lost all the parts on the door frame.

My Patio door closes just fine and the alignment "seems" good, but it must not be because the latch bumps the keeper when I try to close the latch. Then it doesn't fully extend and latch. The workaround is to start with the latch extended and down, (lever halfway) and finish it off after closing. Gu ... (cont.)

I have both the handles (inside and outside.I need the hardware for inside, between handles with the latch behind the handle on the inside and the latch on runner to latch on the hook from the handles., missing when we purchased the home last month. Measurements for sliding glass door lock- 7 3/8 lo ... (cont.)

I'm looking for the strike plate that goes with this locking mechanism. Can you help me locate or where do I get the parts? Thank you.

Which lock/handle do you recommend to replace this lock in which someone enlarged the opening incorrectly. I am able to enlarge the lock opening slightly to get a larger lock to fit. Thanks, Larry

I ordered a steel keeper 89-021 and it the wrong part would you happen to have a steel keeper that i have attached in the picture?

I'm pretty sure the mortise locks on my Cardaco sliding glass doors are the same as your Product Code 82-226 (although whoever installed this one put it in upside down). They also failed to install keepers for both locks. What keepers can I get to go with these locks. I'm selling the house and the ... (cont.)

the door is 1.5" thick, the distance between the screw holes for the handle is 3 15/16" The screw holes for the latching mechanism are close to 4 5/8". The dimensions of the latching mechanism that sit inside of the door are: 1/2" w, 3 3/16" h, 1" d FYI, I don't need an external key hole; in ... (cont.)

Hello, We have a sliding glass door that is about 10 years old. The keeper has broken and I cannot find another one anywhere. It is 3" long, and 3/4" wide. The writing on the glass says PPG Herculite K, Can/CGSB-12.1M 16CFR1201 C11 ANSI Z-97.1 - 1984 1/8U SGCC-250 6021405 thank

Hi, can you tell me what kind of latch/keeper will work with a Mortise Lock, 4-5/8" Product Code: 82-226 (similar to whats in door now) I have a patio door in a new house that never had the latch side installed. handle in on door but nothing to lock into. thanks for your help. Craig ... (cont.)

I can't see a model # or brand name on the door, but here are the pictures. The latch plate is about 7/8" wide. Thanks in advance!

I received my order for a 89-021 Steel Keeper. I must've ordered the wrong one it's about 2 inches too short. My door is a new castle XT SDG if that helps and I need to still keep her

I need to replace a broken mortise lock. I've attached 4 images. My lock doesn't quite look like the part numbers 82-226 and 89-021 that are referenced to another customers inquiry as there is a lip that fits behind the door frame itself( Image 1).

Is the depth dimension of your 89-021 the same as the steel version, 89-021D, which is 7/16" ? The reason I'm asking is I need to replace a Weathershield sliding glass door "Recessed Lock Raised Jam Keeper" part # 972496 (This is not the actual part number off the piece, it's a number I got fr ... (cont.)

I have a Pella sliding glass door that is missing the strike plate. Here are two pictures - the lock recessed in the door and the holes in the door frame for the strike plate. can you tell which strike plate I need from these photos? eric sacknoff

I need to replace the mechanism that's in the photos I've sent. The only markings on the mechanism is "SC". The inside of the handle is 1060-1943. Any assistance would be most appreciated! Thanks! Alan Percival

I have a customer that is missing a door strike on a sliding glass door. I attached pics showing the lockset and a pic showing where the missing strike plate was. I am not sure what strike plate to order. Thanks, Jon

The patio door doesn't lock well because the hole in the frame has rounded out. Do you have something that we can use to solve the problem? Some have suggested replacing the entire door but the glass is fine and so is the rest of the frame. Thanks

The keeper is missing so I can't send you a picture of it. Instead I sent a picture of the handle, an image of the outline of the keeper in the door channel and a picture of the latch. Please let me know ASAP if you can provide the property keeper for our door, Thanks, Michael

My rear door is a slider to the deck and the latch for the lock is missing. No names on the Door. The latch is 4"x5/8". The door is 1 5/8" wide. The latch from the slider only comes out of the door a small distance. The latch must fit within the opening in the slider part of the door to be able t ... (cont.)