Viewing all customer Discussions for:

90-005 Window Sash Lock, 2-1/4"

Either 2 ¼ or 2 ¾ Thanks Toni

Hi, I'm looking for a black Masterview window sash lock, 2 7/8" long, with screw holes 2 5/16" apart (center to center). The screw holes are 5/16" from the edge. What part number is closest to this size? Thank you!

I am looking for replacement sash locks similar to your part #90-005, 009 but with holes 2-3/4" apart rather than 2-1/4". Also, the tongue comes out 3/4". Do you have something similar?

Recently bought replacement latches for my new house that were missing. They were broken, now that they are installed they don't latch after windows is fully closed. It short like 1/4-1/8 is there anything I can buy to ensure they are locked rather than using the the screw at the bottom of the se ... (cont.)

I would like to replace 8 hinges. They were installed in 1994. Cheers, Fred

I think one of these is part # 26-344.. Not sure about the locking one though... Any help?

I need 26 of these sash locks. Not sure of color. It appears to be beige

Need a replacement for a lock that has been broken

This is a left-side lock. It's mounted on the left side of a window. Do you have this same lock that can be mounted on the right-hand side of a window? Thanks

Left and right tilt window latches for better bilt windows approximately 17 years old,replacement parts needed. Anything available? Thanks

I have Nuair windows and they all need new balances and the top plastic piece that is on the top of each side of the window, there are 6 windows. I can send you pictures of the balancer and the plastic pieces that are on top of each window, plus the top latches to hold the windows closed I need 12 b ... (cont.)

Held on by 2 screws with "thumb" lever to Lock or unlock-One on each side of the bottom sash-Need 4 0f these in Taupe color which manufacturer says is actually an Aluminum color

Looking for 10 white window locks for MI windows. number on back of lock is 10R-2 house was built in 2007. Thank you for any help you can give in replacement parts Don

Hi, I purchased two window latch lock 2 1/4" (model 90-005) from you, see photo (top one is your 90-005) The size is correct, but the lock part is a bit "thinner" see 1st photo 2nd photo shows the lock part (my original lock is a bit thicker) My question is do you have the same lock ... (cont.)

Hi Need a pair of sweep locks for a Better-Bilt single hung window (circa 1995) Your part number 90-005 looks right but the screws in my window frame are 2 1/2 inches center to center. Can't seem to find exact replacement searching online. Brown, bronze or black would do. Thanks Regar ... (cont.)

Need a latch like this please. It is from a General Aluminum aka MIWindow window. Please advise

My condo was built in 1988 and one of the black window latches broke off the window. It was the only window that does not have an outside awning or patio cover and tends to get rain directly hitting the glass when it does rain in southern California. The metal looked corroded. Would you please h ... (cont.)

Hi Swisco.....I finally got a side by side pic! The black is the original....would luv to replace it with the white if at all possible. As you can see....original "tongue" is shorter. And this is the problem! I ordered part # 90-005 for my existing Masterview Windows. The dimensions were all c ... (cont.)

The attached picture shows the sash lock with the end of the handle broken off.

Needing slightly shorter sweep lock wing. I purchased a couple sweep locks thinking one of them would work. Both are just a little too long in the sweep lock wing looking thing. My existing lock appears about 1/16th shorter than the ones purchased. Do you have a similar sweep lock with a shorter ... (cont.)