Viewing all customer Discussions for:

90-005 Window Sash Lock, 2-1/4"

I am trying to replace all the window locks on my single hung aluminum windows however each has a plastic fastener that sits under the lock and allows the screw to fasten the lock to the window (picture attached). All of mine are crumbling into dust as I take the locks off the windows so need to re ... (cont.)

top lock to a lawson window

No markings noted on latch. Dimensions included in attached photo.

I AM LOOKING TO REPLACE SOME BROKEN WINDOW LOCKS, MASTERVIEW, BLACK, ABOUT 15-20 YRS OLD. YOUR DESCRIPTION OF PART #90-005 MATCHES WITH THE EXCEPTION THAT THE THROW PART FITS INTO THE WINDOW CHANNEL ABOUT 1/4 INCH. IN ANOTHER DISCUSSION AN EMPLOYEE INDICATED THAT THE THROW OR LOCKING TAB PORTION WAS ... (cont.)

Hello, I have attached three photos: 1.) to identify the Window, tag on Window; 2.) a picture of the spring part to assist in opening and closing window, NEED this new part; 3.) inside plastic trim picture need for bottom of upper window., NEED this new part. Please let me know if I can order ... (cont.)

Need to replace the latch on my sliding screen. I could not find a part number, but the part has the CWS marking on it.

What is the width of part 90-005?

I need to replace channel balance for a sun air window brand the number stumped in the part is 2720 P the metal part is 28 inches long as well i need a window lock and 2 top casing. Can you help me please.

I need the opposite of the lock pictured. The sliding window in question opens left to right. 2.1/4" screw holes. Aluminum window. These locks are different depending on which way the window slides.

Hello Swisco, (Paul & Tom??) A former customer, from the Burlington County area, You helped me out once before (April 2013) by providing me with some Marshall sash locks. 90-005 I'm now wanting to see if you may have the "flush Mount" locks? 2.5" long and .5" wide. In white, photos attached. Le ... (cont.)

The actual MI Window is from Series 740. The ID info located on the actual window are: AAMA-NWWDA-101.1.S-2-97 & H-r45-52x71. The actual decriptive ID located on the latch/lock part is 10R-8 or it could be 1OR-8. I've uploaded a top and bottom photo for you. Please advise if this is a part that you ... (cont.)

Our home was built in 2000 with Pennco windows attached is a picture of the guide.These windows are single hung and take the same sash lock as your 90-005 imwould like to purchase about 4 of these ThanksGarry

Hello, I have Viking window in the house and they were installed in 1992. I am looking for a sliding window latch. Can you please help? the dimension between both installation hold center is 2 1/4" , the hold center is 3/8" .

I saw that someone also needed some parts for the same style of window that I have. I need the plastic piece on the top that goes into the track. Both right and left sides as the tabs have broken off.

I need a replacement latch part for this window. The window size is 52 x 49. The end of the latch handle is broken off.

Hello! We have a 6 yr. old home that has Pennco Inc. vinyl windows. Two of which are not working currently. The length of window is 70" inside wood casing. First one - window will not let me open. In the unlock position, it acts like it is going to open but then stops, as if it's still locked an ... (cont.)

I want to get new locks for PGT windows model SH4000

Can you please tell me your replacement part number for tjis pgt window lock?

I don't know the manufacturer of this window since I can't seem to find any serial number anywhere. The only number I have is 10R-7 (see picture). The measurements are as follows: - Center-to-center hole spacing = 2-1/4" - Total length = 2-15/16" - Width = 3/4" - Lip size = 3/8". ... (cont.)

Hi, I'm looking for replacement locks for my Atrium windows. Some of the locks were left in open position when we closed the window and have broken off. The width is 2 3/4" and I can't seem to find this size anywhere online. Do you sell something similar or know where I can find that size? Most w ... (cont.)