Viewing all customer Discussions for:

21-091 Bifold Door Top Pivot and Guide Pin

Need replacement hardware in pictures above.

Hello, do you have most or all of the hardware to replace all of the part# 4-18? thanks

I have old (1960-70) Strato-fold metal clost doors. I have looked though other posting and beleive I see Two solutions; one for Square hole 5/16" shaft, and one for round hole 1/4" shaft. (It looks like I have the 1/4" round hole) From a July 12, 2023 post I see: 21-003 bottom adjustable threaded pi ... (cont.)

I'm looking for these 3 1/2 metal sliders and the plastic holder for my bi-fold doors.

I need 2 of these for the top of this door and one for the bottomI don't know what these are called.Al

I have missing parts to Strato Fold doors and need 4 guide pins, slide bushings, springs and any retaining items to make these stay in place. Probably from 1970s. Thank you.

Hello Loren and Swisco Help Center, Could you please help me with getting the following hardware: Qty 1 Kitchen window lock for slider window Qty 4 Bedroom window lock for slider window Qty 1 Set of all hardware (excluding door handle) for Kitchen Closet for left door when looking at front of cl ... (cont.)

To whom it may concern: I am interested to buy the spare parts for a Strato Folding cabinet with serial # 38260. I need the kit following: BM-1 - track block BM-2 - Bumper BM-4 - Upper pivot pin BM-5 - Spring BM-6 - retaining ring BM-7 - retainer BM-8 - retainer screw BM- 9 - Upper and lower guide p ... (cont.)

I need to restore a total of 4 doors. Need all hardware: Guide Pins, Pivot Pins, Pivot brackets etc. Door manufacturer unknown. Help.

Trying to redo old bifold doors need all hardware for both sides. Two panels each side (4 total)

I need two of the upper pins, caps and spring in the picture Two of the lower pivot brackets (I think that is the 21-200)Please let me know.William

I am renovating my place and decided to spray paint my old closet doors, unfortunately once I removed the doors the top pivots came off and the little plastic plugs are no longer keep them from springing out. I will need to order new top pivots and bottom pivots along with additional stationary pivo ... (cont.)

Need two end caps. Don't understand some assemblies have rubber washers and some don't. Are they necessary if the spring clip is on the shaft? Don't know if you sell the individual parts for the shafts or just the shaft and all accompanying parts. Let me know.Thanks,Marvin

I bought this one from you but I don't know how to put it

STRATO-TRACK INC. is stamped on horizontal bracing. Tracks are fine.

I had great success with one closet's bifold doors, and I thought the other door was identical. But it turns out it's really different. Do you know which parts I need?

Here parts I need to repair the doors for my brother in law. First is a photo of a diagram and a bottom pivot pin assembly. I am hoping you can get all the info from the drawing for the parts. I would need. I would like to replace all the parts on the doors if possible. Our tracks appear to be good ... (cont.)

I am looking for a bottom guide pin. I need the entire part ( not sure Of there is more than one piece) for my benchmark bifold door

Dear Sir, I have a bi fold metal doors for my closet, I am missing the pins and accessories , please see the pictures attached , I need 12 pins, Nylinder, E-ring or push nut

Good Morning, I have old Strato-Fold metal bi-fold doors that I need replacement hardware for (Serial #26629). I would like to speak to someone asap, to make sure I'm ordering the correct part numbers. I need; Caps (21-105)?, Cone Springs (21-256), and some Pins (complete w/caps & cone springs). ... (cont.)