Viewing all customer Discussions for:

15-087 Coil Housing Pivot

The bath room window opens by sliding up, but instantly slides back down again. Which part do we need to replace? My swisco coil balance part is PAT 5,353,548 WINDOWS SIZE 26(W)INCH * 22(H)INCH (Double Strength Insulated Glass)

do you have a balance like the picture, for my double hung vinyl window. My lower window sash will not stay up when opened. THanks Chuck

These photos are the parts from my window. There are no cutouts in the window frame for easy removal of the part in the jamb.

I have a 35 lb window double hung tilt sash window that will not stay open. Each side of the window uses three series 180 coils, one 15-087 and two 15-086 tandem housings (coils appear to be marked 6 lb / 6 lb / 7 lb - so it should provide a total balance weight for ~ 38 lbs). The lower sash r ... (cont.)

Purchased 15-087 Coil Housing Pivots, 15-086 Tandem Coil Housing, and S180-4 4lb Series 180 Coil Balances. I just don't know how to put them together correctly or install them in the window.

Don't know the brand of windows. They were installed approx. 25 years ago. All custom made. I need at least a dozen sets of the attached balances. Also, the pins at the bottom of the window need to be replaced. A pic is also attached.

Hope you can help me with this hardware. TRACO window, Lower Sash balances and then also 2 sash tilt locks. See attached pictures. Thank you. Denny

I looked up the window balancer via the patent number. Your web site came up. The 15-087 appears to be what I need. I am unsure of the coil spring. Also the pivot bar is completely risted off. I do not see the part number for that. I had to order the sash spreader to remove the balancers. Is there a ... (cont.)

I have two Traco double hung windows that do not stay up. The balance is broken. Its a coil that sprung out and now I have to use a rod to keep the two windos open. How can I purchase new balances that will fit my window. These window are about 10 - 15 years old. Great windows I just need to re ... (cont.)

PAT5353548, window 42"L 26"W

Some of our tilt windows will not stay open. Please help me find the correct balances for them. What is easiest way to remove the balance? PAT. 5,353,548

I am looking for replacement parts. I need the tilt sash lock in the photos and also the correct coil spring. The pivot shoe holds the coil and can be reused. See photos. I was unable to fnd the tilt lock on the site. It slides into a pocket at the top of the sash frame Broken coil balance. t ... (cont.)

will be mailing sample of part [ balance ] to designated address. The window weighs 10 lbs. and measures 27 1/2 w X 23 1/4 H and doublw insul glass. Once part has been determined we will order parts for @ 6 windows.We will need the spreaders,as well.

I'm trying to help a neighbor repair a window spring which is broken. I think the company who made the spring has gone out of buisness. I think it might be invision. I have sent several pictures of the spring. I will have to take the window apart to get the spring out. Need to know if you can sel ... (cont.)

Need several of these. Both left and right. Our windows were installed at least 15 years ago by BEST windows here in New Jersey. I;ve also ordered 10 sets of Tilt Window latches.

how is the proper way to install pivot? do you leave the screw loss so that it lines up with the spring holes or do I put a spacer under the screw. thank you

I am looking for this type of sash balance for a customer. They are Traco Windows. They are spring loaded plastic

I am in need of some window parts and am hoping you can help me. I have TRACO Vinyl windows and am looking to replace the Constant Force Balances has broken on one of the window. picture included, The writing I can make out on the coil is #7.

I purchased the coil housing pivot (15-087). When installed, it does not lock in place when the window sash is removed. Are there internal parts missing? If so, what else do I need to buy to make this work? (I have the coil) Thank you.

I have been searching for these replacement parts. However my dimensions are off. I am coming up with an 1" to 1 1/8" x 1/2" thick your parts are an 1 1/4" will these work I have attached a picture. Also can you explain how the tandem housing is used thankyou.