Viewing all customer Discussions for:

81-249 Glass Door Roller Assembly, Fits Pella

Hello, I am looking to replace the rollers on an old Pella sliding glass door. The 81-249 is the correct dimensions. Is there a replacement that has a "flange" at the bottom to support the roller. My doors are old and the bottom of the slider has some deterioration and isn't supporting the rolle ... (cont.)

Hello - attached are the four photos I took plus one I marked with dimensions (in red ink).Here are what I got for dimensions:2 3/4" Length of roller body1 5/8" Height of body5/8" width overall 1.5" Diameter of roller wheelHope you can read & see these OK.The sliding door is at least 22 years ol ... (cont.)

I need 2 new rollers for my Pella slidding door to the best of my knownlege( ability to read a tape) 1"3/4 High 2"3/4 length 3/4" width. I need to order this before shiping goes out On Wednesday. My husband cave manned it and now I have 2 old dogs who cant get to the ramp (Labs none the less) becaus ... (cont.)

My close-up picture shows my rollers have a flange on them. will your 81-249 work for me anyway?

I haven't taken the rollers out yet (hence no photos) but I know the part number of the rollers I need. It is Pella Roller Part # 0FAT0000 (confirmed with Bella). Do you have these replacements? Thanks in advance.

The bearings are shot but the mechanism is good. Roller is 1.5" od

Hello can you tell me what part number this is.

Do you have original Pella rollers to replace these? The Pella doors I have are from around 1981. Attached are photos. Regards. -Cliff

I'm looking for new replacement rollers for a Pella sliding glass door whose serial number is 16CFR 1201 II SGCC 1921 1/8U, with CTGB Tempered glass. It was installed in 2002. Do you have a roller that would fit this door?

I have a 5' Pella sliding glass door that is used daily with the blinds between the glass that needs new rollers. I believe the door was installed between 1995 and 1998 - I think?? The door has just one hole on each side for roller height adjustment and it appears the roller assembly is 'pressed' i ... (cont.)

Does this part replace people part 0c5y0000 Your product Code is 81-249

Bearing is shot. Have not found a direct replacement with the flanges.

looks like etchings in glass pane read: CTG Tempered 16CFR 1201 IT SGCC- 1805 5/32 u

Please help me find the part number for the wheel unit in a Pella sliding patio door. The part is 2 3/4" wide by 11/16" deep. I don't know how tall. The door was installed in 1987 - 3' wide - model number 31CS. I'd like to have the new wheel units on hand before I remove the old ones. Thanks ... (cont.)

I need to replace the rollers on my sliding door. I see the rollers come in two types, one for old style and one for new style. My door was installed in 2000 so what roller is appropriate for my door. Thank you.

I think this is a 81-244? The door was installed in 1998. Would that be the correct roller to order? I also see they are out of stock. When do you expect them in?

1/84 021581 SGCC-250 ANSI 2-97.1-1975 16CFR1201 This is on the window. I hope that this is accurate.

The roller came from 25+ year old sliding glass door with built in shades. The only info I could find was a Pella logo.

GUARDIAN.DEWITT.I.A.ANSI 2971-1984,SAFETY TEMPERED,SGCC 20201/8U,BS6206-1981,16 CF-R1201II CAN/COSB-12.1-M

Looking for some replacement rollers for a Pella sliding door. The current rollers are (L x H x W) are: 2 3/4 x 1 3/4 x 5/8 inches. I was thinking purchasing either the 81-098 or the 81-249 but my measurements are slightly different. Is there a different roller that I should consider? Thanks for ... (cont.)