Viewing all customer Discussions for:

26-030 PivotTrue Pivot Bar

The pin shown has the number "8" stamped into it. another broken one has "3" stamped into it. I have many windows as this is an apartment house. All pins that have been replaced to date have had the same end cap similar to your pivot bar Model 26-030.Thanks in advance for your help.Harrison ... (cont.)

How do I know which balance shoe I need to get? Below shows 15-175 and 15-177.

Good Morning, I ordered a Pivot True Pivot Bar 26-030 for a vinyl window that does not quite fit. The broken bar is 2 3/4" long with two round holes 1" apart and a "head" similar to the 26-030. It appears that Swisco used to have a part #26-383 that might do the trick but it is not now listed. Have ... (cont.)

I'm pretty sure that the replacement is the 26-030. Any way of determining what brand window this is from? I can't find a label anywhere.

Hello, We have put together a hardware order but have one part that we can not seem to identify. Please see photos of drum roller attached that we need to ID. We would be looking to order Thirty (30) of these. These would be used with Swisco series 152 coil balances for 9 lb. sash. ... (cont.)

Hi I need two pivot bars for one of my windows but, I am having a hard time matching it with one of yours in the inventory you show. Please take a look at the uploaded file where you will see a sketch with dimensions. all dimensions are in inches. thank you

I need 4 these pivot bars ASAP make that for just in case

Pins appear to be aluminum, there is a circle on one side of the pin near the rounded end with a number 1 inside the circle. I'm not sure age of windows? - 2-3/4" long - top to middle of screw hole- 1-1/8"

Hello I?m looking for some parts # & prices if you can help me out thank you

pivot bar piece is approximately 1 1/8" to center of hole a # 7 is cast into piece. Appears to be 1/4"wide perhaps slightly less.remainder of piece is in channel at bottom of window I have been unable to remove it but am able to move it further into channel. Penguin was manufacturer, window is 10-12 ... (cont.)

Since I do not know the brand of the window (It isn't labeled anywhere.)and I cannot locate an exact match for my pivot bar, would the 26-226 make an acceptable substitute? If that is not workable, would the shorter 26-030 TruePivot, (which allows some adjustment in placement the holding screws) be ... (cont.)

Overall length might be 2 3/8" if bar is straightened.

I am looking for this part that goes in upper corners on the outside of a double hung window made by Kobe-kolbe.Its a soft metal pivot that allows the window to move up and down.This pivot fits in a bracket in the window track.Round head with a rectangle raised price on top of round head.Pics show i ... (cont.)

Looking for tilt latches and pivot bars for vinyl windows. Found pivot bars that match looks like part number 26-030. Can

Hi, I did see either a number 9 or 6 on the piece itself

Need spring slides and shoe that are in window frame and also the bar that hooks into the that is screwed on bottom of sash.

I have a house full of windows that won't stay open because of this part. I see many similar on your site, but none have the "oval" screw holes. There is a "4" on the part. The bar measures approx. 2-5/16" long and about 1-1/2" from the top to the center of the first oval and 11/16" from the center ... (cont.)

Found this item in the picture that appears to be a broken pivot bar. Window obviously does not slide up and down and remain intact. I do not know the window manufacturer of this vinyl double hung window. It looks a lot like a 26-030, but the part in the frame

2

Pretty sure that I just need to replace my pivot bars, but I don't know which ones will work in my windows. The photo is of one still intact in another window in my house. The broken piece I have has two circles on it and in one of the circles is a 6 or a 9. The windows were made by Energy Exteriors ... (cont.)