Viewing all customer Discussions for:

39-027E Ellipse Style Single Arm Operator, 9-1/2"

Hi, I have some really old looking window cranks. I have 14 total. 5 are broken. I would like to replace them, if I can find the right part(s).

I am pretty positive I need 2 -(left and right)Truth window casement operator parts #39-027E. Here's what I need to know before I order. On YOUR measurement for the single arm in a part photo, you have 9 1/2 inch arm. In YOUR measurement drawing in one of the actual photos, it says 9 1/2 inch arm f ... (cont.)

Have you any idea if one of your crank's will match the operator shown in my picture? It is a "truth" operator. I'm looking to replace one that broke. Thanks in advance.

Hello, I need to replace the operators on a few old Possi casement windows. I have attached a picture of one for comparison. The only part number on it is 07702-00. In one of your previous postings you recommend a 39-014 and 39-013. Would your part number 39-028 be an exact replacement? Also, the ... (cont.)

Hello, We are looking for a replacement crank for an old Andersen window, item #7073B. I did find a thread online that suggested your 39-027E and 39-028E however the arm doesn't have the same bend in it. Please see attached photo. If you do not have a comparable crank, do you have just the corkscre ... (cont.)

Markings: Truth, 45034-lh. Arm looks to be around 9.5" from pivot to end.

I purchased 39-413.The offset is not correct. I need a down offset, this is an up offset. Can you help me with the correct part number?

Dear Swisco, I am seeking replacement hardware (hand crank, worm gear, bracket, and toothed lever arm) for a Patriot brand kitchen casement window. The spline for the hand crank is stripped and the worm gear / toothed lever interface is also stripped. The two photos show the spline and the visi ... (cont.)

Do you recognize this part? If so, what do you recommend as a replacement? Please review attached photos for hardware identification Thank you Joyce

I recently purchased two replacement operators (39-028E & 39-027E). They fit nicely and will work with the windows. However, the plastic wheel on the end of the new operators did not match the existing tracks. The old tracks and old operators had the thin, flat plastic wheel. Now I need to replace t ... (cont.)

Our house was built in 1956 with Anderson casement windows. Now a number of the window operators no longer operate. The number etched into one of the operators is 2420. One of the operator arms is 7 1/2" long (left hand), another is 9 7/8" (right hand). Do you have replacements for these and ho ... (cont.)

It's a Patriot brand window in my Kitchen

Two-window set in kitchen. Left crank was stripped. May need to replace both for matching pair. Left side has been removed; picture of installed crank is right side.

When turn handle - gearing in base jumped or skipped a gear so unable to open and close. I am the home owner but have an experience handy man guiding me and will do the work.

Good Afternoon. I am looking for a replacement window crank operator. My previous model was by Wright. Dimensions are as follows: Base is 4" wide and 3" long. Length of moving arm is 9". Holes for screws must go downward into the wood. This is a right window crank.

The controller arm is 7-7/8" long to the bend. I read that this company is no longer in business. Do you have a substitute for this unit? We need to replace probably 4. Thanks for your help.

The 35-920 looks like it will work for me but on my Windows the screw holes are below the track Will that make a difference ?

Only identifiable markings are us patent 6,247,270. Length of arm is approx 11in and doesn't fold/bend. Help!

The screw holes are 8cm and the arm is 11 inches. There is no manufacturer only a patent number on the base which is 6,247270. Can you suggest a replacement part

looking for crank and arm for casement window