Viewing all customer Discussions for:

39-028E Ellipse Style Single Arm Operator, 9-1/2"

is 30-028 avail in lefts and rights ?

I'm hoping you can help me, we are looking to replace one of the window operators for our casement window. Attached are several photos with measurements. We have tried standard replacement operators from the hardware store, but have not had any luck. The depth of the crank is too shallow on most and ... (cont.)

I am in need of an operator like the one above except that the arm needs to be 9-1/2" and I need the opposite side. It is for an MI (Metal Industries) 1470 Series casement which has been discontinued. This operator needs to match those of 3 other windows in the same room so the new style isn't a g ... (cont.)

What is the number for the left hand version of the operator Caradco window crank 39-028?

The windows in my in-laws home, built 1973, in Wisconsin have the attached mechanisms for opening and closing. The photo of the back view shows the following numbers: RH 40056 3 I'm assuming the "RH" means right handed - is there also a left handed version? Not sure how many of each I nee ... (cont.)

I have 2 casement windows that new new hand cranks. the windows are good but the hardware is worn. Please see photos and advise. The width of the crakn is about 4 1/4 " wide. The Corado windows are about 40 years old. Bob

I need a replacement left handed crank for a wood framed window. "Fred Reuten Inc." is on the opposite (still installed/working) right handed crank & glider. No other markings or model numbers were found. I have included photos of the right handed crank which is still installed & operational. I have ... (cont.)

I have old Marvin windows that I am trying to service (circa 1980). On one window, the crank arm is "twisted".. and I have no idea how because that thing is solid. So when the window closes it forces the cover wood out and the window does not seal right. I need to replace it. The cranks you have ... (cont.)

I ordered a caradco window crank 39-028. You sent me a left hand and I need a right hand. Do you have a right hand? Can I return the left hand? fred spencer

I am trying to match up some crank assemblies for Caradco windows. On the castings they say Truth and on worm wheels R30842 and L30842. I am physcally in Wisconsin and the windows are in Kentucky. I believe the nominal width of each side of double casement window is 16" and I have others that I ... (cont.)

Do you have a replacement for this part? It is from an Anderson window. I also need exact same version but the arm is 2" longer than this one. Can you help? Thanks, Matt

left side crank - base = 4" length 1 1/2" depth crank = 2 1/2 in length 2" depth

I need to replace several casement window operators. They are from a house built in the last 60's. The crank handles have Malta on them. Otherwise, there are no distinguishing marks on the window frames or cranks. The bottom of the cranks have a LH or RH depending on whether they are left or rig ... (cont.)

Any idea if you have these parts

I have a caradco window. See attached photos. The dimensions on mine match your #39-028 and the one I need that is broken is a match for your #39-028. main photo with the crank spline on the left of the housing. On your other photo you have on your site for the #39-028 it is actually for a right ... (cont.)

I need to replace the right and left Truth operators, which are 10-inch straight-arm. The operator is stamped 45261 and marked "XX202003 1029" where "XX" are two smudged digits I can't make out. The two-bar jointed slider, which I don't need, is marked Truth 30818 and is stamped "PRY TO REMOVE SASH" ... (cont.)

I need the window crank mechanism for this window. It is an all aluminum window. This is the left window (from the inside), but I need the cranking mechanism for the RIGHT side. The crank arm comes out of the track so that's why I need to replace it. (I think the nylon wheel that rides in the trac ... (cont.)

I recently ordered replacement Anderson Straight Arm Operator, 9 3/8" Arm kits for left and right. We received the kits and the mechanism that is mounted on the Window sill is wider than the original one we have. Our present one has 3 4/16" distance between the two screw holes....the one we receiv ... (cont.)

I have casement windows manufactured by MI Windows & Doors. The series # is 1470. Will any of your products replace the operator mounted on the left-hand side of the window?

Hi - Just discovered your company and am very happy that I may be able to replace parts of broken casement windows instead of getting new windows! I have 1980 Weather Shield Casement windows. Am stumped on how to remove the crank handles. I do not see any set screw visible. Does the handle just ... (cont.)