Viewing all customer Discussions for:

58-135 25ft Bubble Seal, 3/16" x 11/32"

Looking to replace old weatherstripping. The plastic base is approximately 3/16" wide. The top portion that is foam filled is approximately 3 - 4/16" wide. The overall height, from the plastic base to the top portion is approximately 1/4" tall.

I have Jalousie Windows with t slot bubble seals . They are 3/16 t slot width and 1/4 inch dia .. You have a t slot that is 3/16 x 3/8 # 58 135 . Do you have the 1/4 and if not do you think the 3/8 dia will work ok . attached is photo of the existing bubble seal . I used my vernier to measure the di ... (cont.)

How do I put the bubble seal into my screen without destroying it? The old peace in my screen slides back and forth. Thanks!

Hello - I am looking for the correct weatherstrip to replace my Patriot Windows weatherstrip on the bottom windows.

The width measurement of the plastic strip is 5/16" with the gasket itself being 1/4" I've included a picture of the maker and model of the windows.

We purchased this part# 58-135 thinking it was a perfect match, however it was not. Do you have another item that is like ours, the T part needs to be rubber.

Hello, In our church model 5 years ago, we got new metal doors with windows in them. The weather stripping in the picture has worn and ripped (it is made of a rubber material, no plastic or metal parts) and it slides right into a slot on the door. I think it is weatherstripping. The width of the " ... (cont.)

Photos of weatherstrip I`m looking for

I have over 15 3-part crank out windows in a 1965 condo. I love the windows, but they need new seals. Photos are attached. The little seal that runs along each window has practically no "base extension" but the portion that slides in the groove is 1/8 inch wide. I fear 3/16 may be too wide to f ... (cont.)

I have 20-year-old ALENCO aluminum windows that are beginning to get drafty. I found the correct 3/16x3/16 grey wool pile on your site, but there are two other parts I cannot find: *3/16 rubber bubble seal installed in the bottom sill *Vinyl extrusion along the sides of the opening that contact t ... (cont.)

Can you give me a quote on this if you can match it.

Hello, I have a hollow bubble seal that measures 3/8 bubble and 9/32 T. Do you carry this size? If so, what is the part number? It's the seal on a sliding glass door.

The closest I can find is shown in 1380 pdf.

Is a special tool required to install #58-135 or #58-134 insulation at the bottom of a window? Does the sash need to be removed before replacing the insulation strip?

I made a drawing, but I did not have a program to convert it to any forms that you would accept, so I took a photo of the screen. The second photo is the profile I was drawing. the third shot is the outside side of the strip. Will the bubbles keep the window from going down far enough to lock? ... (cont.)

My wife & I recently purchased a home built in 1999 with Better Built single hung tilt windows. The rubber seals/weatherstripping on most of the windows is hard/brittle and not making a good seal. The weatherstipping slides into a T-slot and looks like the T portion is 3/16" wide and the rou ... (cont.)

This weatherstrip fits into a 3/16" channel and is approx. 1/2" high to seal the bottom of the window to the sill. Do you have a product which will suit this application? Thanks, Scott

Hi. The weather stripping on the bottom of the window has dried out and rotted. Where can I get a replacement? It seems to slide out the end.

can you help me find it

I have three (4'x4') aluminum basement windows that need the weather stripping replaced. I think the sides (I included 2 pics- IMG 0876/0878) and the top use the 9/16 commercial bubble weatherstrip. Please let me know what you think. The bottom uses a different type of weather strip and I can ... (cont.)