Viewing all customer Discussions for:

58-135 25ft Bubble Seal, 3/16" x 11/32"

Dear Swisco, I searched your pictures and can not find this weather strip. I am not sure if I am looking in the right place. If you can offer any help that would be greatly appreciated. Thank you

Hi, This is a part of a sliding window. To me, it looks like there are two parts glued together,but because of sun, they separated. I would be happy to find anything that may fit that small channel. There is part number or anything. Hope you may help me find the part. Thanks, Milosh ... (cont.)

ATTACHED IS A COUPLE OF PHOTOS FOR A BULB WEATHER STRIPPING IM HAVING TROUBLE FINDING. IT IS FOR A CASEMENT WINDOW, AND THE WINDOW STICKER IS TOO FAR DAMAGED TO GET ANYTHING FROM IT.

I have CertainTeed Bryn Mawr casement windows and MI Co. referred me to you for replacement weather stripping for these windows. Each casement is approx. 26" x 64". There a 11 windows on my porch but only 4 need new stripping. Thanks for any help.

Hello, I have been looking everywhere for replacement weatherstripping, please see the attached images. I need about 12 feet of the T-Slot weatherstripping. It says Q-LON on it. Any ideas??

Bubble Weather Stripping for CertainTeed Window(30 years old)

This seal is from my front door, original to the house built in 1984. I have searched every where but can't find anything that can replace it.

The flange is 0.25" and the bulb is 5/16". No neck on flange. From a 1980s Atrium commercial door.

Tube is close to 5/16 and T is close to 2/16

Looking to replace old weatherstripping. The plastic base is approximately 3/16" wide. The top portion that is foam filled is approximately 3 - 4/16" wide. The overall height, from the plastic base to the top portion is approximately 1/4" tall.

I have Jalousie Windows with t slot bubble seals . They are 3/16 t slot width and 1/4 inch dia .. You have a t slot that is 3/16 x 3/8 # 58 135 . Do you have the 1/4 and if not do you think the 3/8 dia will work ok . attached is photo of the existing bubble seal . I used my vernier to measure the di ... (cont.)

How do I put the bubble seal into my screen without destroying it? The old peace in my screen slides back and forth. Thanks!

Hello - I am looking for the correct weatherstrip to replace my Patriot Windows weatherstrip on the bottom windows.

The width measurement of the plastic strip is 5/16" with the gasket itself being 1/4" I've included a picture of the maker and model of the windows.

We purchased this part# 58-135 thinking it was a perfect match, however it was not. Do you have another item that is like ours, the T part needs to be rubber.

Hello, In our church model 5 years ago, we got new metal doors with windows in them. The weather stripping in the picture has worn and ripped (it is made of a rubber material, no plastic or metal parts) and it slides right into a slot on the door. I think it is weatherstripping. The width of the " ... (cont.)

Photos of weatherstrip I`m looking for

I have over 15 3-part crank out windows in a 1965 condo. I love the windows, but they need new seals. Photos are attached. The little seal that runs along each window has practically no "base extension" but the portion that slides in the groove is 1/8 inch wide. I fear 3/16 may be too wide to f ... (cont.)

I have 20-year-old ALENCO aluminum windows that are beginning to get drafty. I found the correct 3/16x3/16 grey wool pile on your site, but there are two other parts I cannot find: *3/16 rubber bubble seal installed in the bottom sill *Vinyl extrusion along the sides of the opening that contact t ... (cont.)

Can you give me a quote on this if you can match it.