Viewing all customer Discussions for:

58-135 25ft Bubble Seal, 3/16" x 11/32"

Small seal on top of doors that fits into grooves. These are storm doors with impact glass and the seals are needed. Slightly oversized would be preferred since the doors appear to have 'sagged' over time (something even 3/8" would probably work). Measurements are 'rough' due to the age and I cannot ... (cont.)

The hard plastic base is 1/4 wide and tube is 3/8 inch wide

Hello there, Hoping you can help me find replacement weatherstripping for my front door. I've attached photos of the seal in the flange, and of a cross section. Dimensions are: Overall height = 3/8" Overall width = 7/16" Bulb width = 5/16" Base width = 1/4" Base extension is difficult to measure ... (cont.)

Cerrainteed vinyl windows installed in 1989. Need t-slot bubble seal 1/2 diameter.

These pictures show my weatherstripping at the bottom of what I believe is an MW Window. They were made in Rocky Mount Virginia about 30 years ago. The windows are in great shape, but I would like to replace this aging weatherstrip. Pictures show the base of the weatherstrip and the round body that ... (cont.)

Trying to find the right weather stripping to replace/refresh my Owens Corning windows. House built in 1949, windows replaced in 2001. Windows are still in good shape but some of the stripping (the stuff outside facing) is brittle and starting to fall off in the middle. The foam part seems OK but c ... (cont.)

Windows were installed 2013 and the weatherstripping on the bottom panes has shrunk in length. It's attached by sliding it into a "T" channel in the aluminum frame.

looking to replace this on all the windows in my home but can't seem to find the correct part that is similar in size. everything i find seems to be smaller

Thank you for your prompt response, I do not have at this time a better picture but will be getting off work today around 3:00 central time and will take a better picture then and will send them to you. I am looking for a dark gray or black replacement. This is the only tag from Simonton I could fin ... (cont.)

Hello Paul, I have a question about a aama/nwwda 101/i.s 297 window other numbers found were h-r25-48x78 and H-r50*-36x74 (modif). So, your company Swisco has two different models of T-slot seals (1) is 58-182 and other is 58-183, one has full foam and other has foam with a hole in center. The prob ... (cont.)

Hi, I am looking for 3/8" diameter bubble seal with 1/8" base extension for a house entry way double door. Preferably in black. Not the easiest find in the big box parts stores / Amazon. Base slides into channel along the side of the secondary door t-astragal. Is this something you have in stock? J ... (cont.)

Need replacement weatherstripping for bottom of Bottom sash of Harvey Wood (Majesty) replacement windows. They are 12 years old and the plastic bottom of the weatherstripping has crumbled. The pictures should tell the story. A foam tube with hard plastic flat bottom. Seems to be about 3/8" wide an ... (cont.)

weather stripping for a Simonton window - number 3975053/01-2 manufacture date 11/15/2004

Dear Swisco Representative, 34" long x 5/8" wide for white seal first three pictures. If need more details let me know. Thank You Yes I want to replace all the glazing to windows as all images sent. I have 23 windows to re glaze.

Need help in finding and replacing weather stripping on the bottom of Alcoa Aluminium windows installed in 1992 when house was built. Stripping is 1/2 inch wide

Windows were made in 1989 by Georgia Pacific for NuSash. This stripping goes around the window frame. We need to replace this stripping as it has come out over the years. Appears to have foam inside the stripping.

Do you have a bubble seal that could replace the gasket on the Truth Hardware crank windows. It looks like 25ft Bubble Seal, 3/16" x 11/32" Product Code: 58-135 matches the best in terms of measurements (mine is 5/16" diameter and the widest part of the "t" is 3/16"). The bottom of the seal I have i ... (cont.)

Do u have or similer

Looking for the parts above, all seems like the pivot arms are missing the screws.

Mfg & installed 2004. Do not have model no