Viewing all customer Discussions for:

26-405 Rounded End Pivot Bar, 2-7/8"

Hello! I am in need of replacement pivot bars. Do you have any that could replace the ones in the picture. I have looked through the site and am unsure.

Hi, I need coils for both sides of my windows. Can you identify the coil that I need from the picture? 12lbs? Also, it appears difficult from the minimal space to replace. Is it possible to replace?

Hello, I need some guidance on obtaining the correct pivot bar replacement part as well as replacement screens for the model vinyl window sticker in my photos. We need 1 pivot bar and 6 or 8 ready made screens. We also need thicker felt for sides of window sashes there are air leaks. Thank you!!!Mar ... (cont.)

There are three set of numbers on the balance. Patent # 6,378,169 One of the coils has 5FF and the other coil has 6FF. Any help would be appreciated. Thanks!

Trying to Locate this discontinued sears vinyl double hung window coil balance and 3 " round end pivot bar. The width of the coil is 3/4" and has a much bigger cutout on top. The matching mount bracket that goes with balance is 16-031 which is plastic. I need 2 - 8 lb coil balances. If this is not ... (cont.)

Thank you!

I have several windows that need coil balances. The photos are from one of them. I tried a set of S140 5lb coil balances, but the bar on the bottom of the window doesn't fit into the window carrier part of the balance. Is there a different model that will fit the bulb on the end of that bar on th ... (cont.)

Please see attached pictures of removed parts from the window on one side only. I need all those parts eight of them four to the right four to the left of four windows. Please call me prices and shipping delivery.

Hi I am Emily from Glass Doctor in Dothan, AL. I am needing some help finding a replacement part for the attached pictures. The stamp on the coils reads 9 A P and on the white piece reads 9 R. Thank you!

Hello,The attached pics are from a Croft vinyl series 20 window. The pivot bars needs replaced as one is broken and one is bent. It appears to me this pivot bar is about 2 3/8" long. Any assistance you can provide would be greatly appreciated. Thanks, Matt

I'm trying to find the coil balance like the one shown in the picture, which has a flap under the hole. Thank you

I would like to purchase a replacement for this. Can you help me?

Hello, I just purchased a house with older Anlin Catalina windows. They are in decent condition overall, however all the hardware needs to be replaced. Anlin themselves referred me to your company for parts as I am outside of the windows warranty and their service department is over capacity as it ... (cont.)

I believe the balance is a S210-10 (it says 10 on the side of it) I can't find the pivot pin on your website I believe the bracket is a 16-030 I need to know all 3 part numbers since I need to order multiples of each part Are there any special tools needed to help with the install? Thanks Steven ... (cont.)

Replacement coil balance needed and matching pivot pin

Trying to find these

I need help identifying the correct part number I need for my windows. Please see the attached picture below. 8 double coils (4 left & 4 right) 10 pins 2 single coils (1 left & 1 right 5 top locks (3 right & 2 left)

Hello, I was wondering what pivot bar would be used with the S140?15 coil spring set.

I'm thinking I need Tilt latches 26-442? Pivot bars either 26-405 or 26-226? Pivot shoes 15-215? Can I just replace the pivot shoe and use the old coil balance? If so how to separate it from the coil balance, I didn't see that in your videos only how to remove the shoe from a different type of coil ... (cont.)

These are springs from a 16-pound window. I would like springs and complete assembly. there is a number on the tilt show.560CSR Pat# 5704165.