Viewing all customer Discussions for:

26-410 Tilt Latch Pair, 1-13/16"

Can you please help me identify this tilt? I have been able to identify the balance(s) for my windows but the tilt is proving difficult. The windows are Ply-Gem 3700 series, but there is no other info on the window/hardware.

Dimensions are 2 13/16 long, 3/4 wide, 1/4 high, holes are 1 13/16 apart. Center of hole to latch is 3/4. Thank you !

This appears to be a common problem with the old Pacific Industries window latches - they break easily. I have a houseful of vinyl single hung windows and, before Pacific went out of business, I had purchased a number of spares that have now all been used, so I am searching for an alternative solut ... (cont.)

Hi, I'm looking for a tilt lock, it goes on windows in a mobile home. I don't see any part numbers on the tilt lock or window. The dimensions are: Length: 2.7" Between holes: 1.8" Width: .950" Thick: .3"

length without the catch 2 7/8" (all dimensions could be plus or minus a 1/16th) width 3/4"; distance between attachment holes 1 3/4"; distance from hole closest to frame to frame 3/4". Could be an Alenco V2807 BUT in black.

Manufacturer is PlyGem #3753. The broken release assembly is a LEFT hand side in black. The locking tongue is broken off during installation and the installer is long (3 years)since gone. The photos depict a right hand sample which was easer to photo than the actual left hand broken assembly. Ple ... (cont.)

Left and right tilt window latches for better bilt windows approximately 17 years old,replacement parts needed. Anything available? Thanks

I'm looking for the metal pivot "pins" that stick out from the lower sides of the moving windows themselves, and the things on top of the moving window that keep them in the track. It says Care Free on the lock, and has the spiral dampers.

I'm looking for replacements for surface mounted latches as shown in the photos. Based on my measurements, they appear to be 2-23/32" L x 1" W x 5/16" D with a hole-to-hole center distance of 1-13/16" and latch edge to hole distance of 1-5/8". Product Code: 26-410 seems to be pretty close. Do you ... (cont.)

The lock is White, approximately 3.5" long, a little over an inch wide and the screws are 2" apart in center. The lock is flush mount and all plastic.

The last week buy in you store one part lath window 26- 177 and 26-176 but is to big

The windows were installed in 2006. No brand name could be found. The distance of the screw hole centers is 1 3/4" Need both right & left sides.

Need the following latches for a Philips window. I believe the lathes are 3 in by 2 in and the end piece are 2 5/8 by 2 3/4. Let me know if I am in the right ball park.

Boreal tilt lock for tilt out vinyl window and a snap in channel that covers the spiral balance. Cant find them on your site ;^)

Top and bottom of latch sent as picture. The following are as accurate as I could get: Center of hole to center of hole : 1 13/16" Width: 3/4" height as it sits on the window (thickness): 1/4"

Philip single hung Window tilt latches replacement part - your 26-193 & 26-194 Rollyson Tilt Latches. Will these work if mine measures 3 inches? I do not want you order them if they will not work. I have already checked Menards. They actually recommended to check online. They did nothing that I woul ... (cont.)

Hi I have a mobile home with Philips care free windows built 1992/1993. Have you had luck with the 26-410 as a replacement latch? The dimensions seem about right.Thanks for your time

Dimensions: Length 2 7/8 Width 3/4 On Center holes 1 1/2 Height 1/4 White Atrium does not have latch!

Hello, My Philips Products window latch is 1-13/16" from center hole to center hole. Do you have a Rollyson window latch that size? I need both right and left. Thanks!!

I am looking for tilt latches for Philips Products vinyl windows in a mobile home. The hole spacing is 1-13/16 to 1-7/8", over all housing length is 2-15/16",housing width is 13/16", housing depth is 1/4", catch projection is 3/8", color is white, surface mount style. Thank You Duane ... (cont.)