Viewing all customer Discussions for:

26-226 Pivot Bar, 3-1/16"

Hi, I thought I'd ordered the correct replacement pivot bar (265B) but apparently I was unaware that the former bar had threads in it. The hole on 365B is also just ever so slightly smaller than the old screws. The hole lines up fine with the existing one on the sash, so other than these issues I ca ... (cont.)

Hello, Need help identifying broken pieces. One has a # 8 and the other a # 3 Thank you, The measurements are "roughly" 2.75 length, 1.5" ctr of hole to head, the head itself is roughly 3/8" overall and that center piece in the middle is roughly ¼"

Hello, Need help identifying broken pieces. One has a # 8 and the other a # 3 Thank you, Tammy

Couldn't find it in your web.

Need an early pivot stright pin for a Harvey replacement tilt window. The pins first is 1" from the pin head . There are two holes.

Hello - This is a pivot bar for a Paramount window. It is 3" long in total. There are 2 screw holes opposite of the pivot point. One is 3/8" from the inside and the next is 1 3/8" from the inside. There are two little nubs that stick out on the sides and one little nub on top There is a marking: th ... (cont.)

Hi?I need help. I have replaced the coil assembly, but the pívot I chose doesn't fit. Maybe I chose the wrong parts? So, I've decided to start over. Here are the original parts. I need to fix two windows. I would appreciate any help you can give. Thank you, Tina

Bought a duplex need the tilt latch, (top corner),pivot rod, and coil spring shoe can't seem to find a match on your website and don't wanna order the wrong part thanks! Can't seem to find any numbers on the parts themselves

broken tilt wash pivot pin on q2 window

In 2007 we had windows replaced by Regency Windows. They are the double hung vinyl. Two of the bottom windows broke and we need the pivot bar and the pivot lock. In searching your web site I cannot find a pivot bar to match the one we have. The pivot bar is 2-3/4 and one has a number 8n it and t ... (cont.)

I need help identifying which replacement pivot bar I need. I have attached photos of a good one. It is 2 inches long and 5/8 inch wide. Any help is appreciated as I didn't see it when I browsed your site.ThanksNeal

Hello- I'm not sure what this is, let me know if you need any other information. Thank You

I currently must replace a two coil constant force balance system on multiple windows and it looks as though many parts have been discontinued. In reading through helpful posts I have come to what I believe will work but would love to have confirmation. The photos attached are from one side of the e ... (cont.)

Hello,Your assistance identifying my window parts would be greatly appreciated. I have attached photos. I labeled the photos with what I'm looking for since I don't have the proper nomenclature.I would like to identify 5 different parts, and will be ordering multiples of each as I own several rent ... (cont.)

I have trouble finding this pivot bar and do i need to change the coils cause the slider in the open position is hard to go up and down.

Need replacement hardware for KVw tilt single hung 20+ Years old can you help? Looking for complete repair kit for these windows.

I recently ordered a pivot shoe and pivot bar. The shoe works perfect, in fact I need another for a different window, but the pivot bar didn't work. Picture on floor is of the good bar; one on window is the new one that doesn't work. The holes just don't align to a good spot for how long it needs to ... (cont.)

I can not figure out what pivot bar to buy. This is the one I took out that broke. Could you help me

Hello I have enclosed pictures of the parts I need help finding. Thanks

I need help identifying the parts I would need to fix some double hung windows.In the pictures, the pivet bar is about 2 3/4" long, 1/4" wide and 3/16" thick. It is held with 2 screws that are about 3/4" apart, center to center. The second hole is oblong. The end of the pivet bar is about 3/8" in di ... (cont.)