Viewing all customer Discussions for:

26-235 Sash Release Finger Lever

I have a 2"x7/8 inch finger release Nylon window sash release lever that I need. it's 2"x7/8" with two legs going into the top of the window. The legs are about 1/4" wide and they have a 5/16 depth. I need at least 30 of them for an apartment building that I just purchased. There is nothing in t ... (cont.)

Hi Swisco, Just talked with you by phone, here is the tilt latch actuator I amlooking for. Not sure of window brand. Let me know if you havesomething like this! I need probably 15-25 of them. Thanks!

Hello! I am looking to get replacement Window part that releases the tilt to the window. I'm looking to get 4 replacement parts of the images above. I couldn't get a part number to the window but I do have the form of when the windows was replaced in 1996. Thank you for your help! ... (cont.)

Hi, I would like your assistance in identifying this replacement part to tilt open the windows. Also when installed are they removable to use on more than one window, or should I buy enough for all the windows (ie do the snap in and stay put)? They are 2 in long, about 7/8 in wide and the prongs are ... (cont.)

Tilt window latch brown

Looking for replacement parts for tilt latch and locks. The top item next to the tape measure is the good one, the other two are broken parts that need replacement. The bottom item is the tilt latch handle that broke off. The item in the middle is the window lock latch with a broken hook. Do you ... (cont.)

Your part 26-234 in the foreground has the proper clip width and thickness but the depth isn't sufficient. My clip (in the background) is similar the the Pittsburgh guy's. It has much longer prongs and two offset raised guides.

Hello, Hoping you can help me.....I need to replace several broken tilt latch buttons for my windows, pics attached. They are 2" long, 1/2" wide, prong is 1/8" thick, in between the prongs outside edge to edge is about 5/8". Similar to ones on your website but don't look exactly the same. Window is ... (cont.)

I am looking for replacement window latch release tabs. These have become yellowed, brittle and broken at the little catches circled in blue. They are about 2 inches long and 13/16th wide. Those dimension are not critical, only the two feet that drop into the slider to release the tilt latch. Th ... (cont.)

Have broken sash latch releases for tilt in vinyl windows. Need 8 (eight ) as they are all broken and missing the catch prongs

This part slides to allow window to get removed. Do you have replacement?

The first 3 pictures are for a 30 inch long trim piece that attaches into the top of interior window frame and acts as an insulator between the top of the window and the frame, it has felt material. I need two of these. JPEG 1 and 2 are pictures of a tab / lever that allows the window to tilt down ... (cont.)

I am looking for some replacement parts for our Alside UltraMaxx double tilt windows that were installed 2002. The three parts I am looking for are: 1. Pivot bar - couldn't get full measurement because it broke off. 2. Tilt latch activator 3. Cosmetic cover that covers tops and bottoms of wind ... (cont.)

Hi,We have 4 tilt windows and most all the shoes need to be replaced. We would like to order replacement shoes, pins and sash releases but are not sure of the correct replacement parts and are hoping you can help. Attached are pics of the shoes, pins and sash releases. The shoes looks to be about 3 ... (cont.)

Side piece cracks off

There are no manufacturers labels or information. These windows are old and of an unknown age. Top is 2 inches in length by 7/8ths inch wide. The clip under the center is 1/2 inch.

I have Mastic windows where the tilt release levers are brittle and breaking. I do not see any on your website that have the same measurements. Wondering if I missed the one I need or maybe you have others not listed. OR maybe a substitute?

I need to buy the Tilt Latch Actuator spare part, it has a broken leg and it seems that it is not manufactured, I can replace it with part 26-215, which comes complete.ThanksHernan

How do you find a tilt latch and a thumb knob to go with it ?

Please advise if you have these tilt latch, will await reply. many thanks