Viewing all customer Discussions for:

32-031 Rear Drawer Guide

As attached, can I find the same to buy

this guide is from a Harden furniture co. bedroom set about 30 years old Looking for replacements that have a tongue that extends into the track shown above. the old one has ronthor nyc on one side and a patent number 2847233 on the other side. the tongue keeps the drawer from rubbing on the wood ... (cont.)

Need to replace some rear drawer guides on dressers that were bought about 35 years ago. Guides were made of Teflon, and some finally became brittle and cracked. The design of your guide 32-031 seems to be the correct one, but some of the dimensions I measured on the intact ones vary just a small ... (cont.)

have a 15 year old Stanley Furniture cabinet with drawers and the plastic part attached to the back of the drawer to hold the drawer on the track broke. Do you have a replacement or something similar. Sisco 32-031 is the closest I see but you have a lot more info than I do. Thanks ... (cont.)

I am looking for a rear drawer glide for a desk drawer. The opening of the original plastic rear drawer glide is slightly less than 1-3/16 opening wide nd this inter locks on a 1-1/8" wooden t track the open slot is greater than height 1/4" The T Track is good condition I need only the plastic ... (cont.)

I need two of the ronthor #2857233 rear glides, and i se the 32-031 was suggested, but it doesn't have the little shelf about the opening for the glide. Is there a different on I should be looking for? Attached is a picture of the glide.

Rail guide for Bassett bureau

Attached photos. 1 of 4 plastic rails that slide over wooden rail in dresser. These are Attached to the bottom of each drawer. Part # 3185530. Would I need to replace the whole assembly or use just white plastic part 32-031 by itself. Appreciate your feedback. Thanks Czar

Hello. I have an inherited nightstand and the drawers do not stay in when pulled out. The drawer guide was broken on one and I removed the remainder of the plastic. The other was already gone. There's a metal rail inside the cabinet body. I don't see evidence the drawer ever had a rail. Is the drawe ... (cont.)

Searching for drawer guides for the top of a bar cabinet chest. The front of the guide has patent 2857233 and the back has RONTHOR N.Y.C.. I have had the bar for 47+ years and there are no identifying labels or numbers on the cabinet. It is solid wood. The runners are on the bottom of the counte ... (cont.)

the rail that my drawer guide hangs from is wood and worn. Can I add epoxy to the top edge of my drawer guide so that the guide does not fall off of the worn rail? Thank You

I am trying to find replacement pieces for a few drawers on my Lexington high boy dresser that are broken. The drawers no longer run on their slides and the rear mount drawer slide guides are broken. Do you sell parts that I can use to repair this? This has been and exhausting and frustrating hunt ... (cont.)

Drawer Guide REISSS MANUFACTURING COMPANY N Y C R 26 .PATENT: 2857233 DIMENSIONS OF GUIDE PATH : WIDTH 3/4 INCH DEPTH 1/4 INCH

I am seeking 6 of these. The patent number is Patent 2857233 D

Do you have the rod that connects to this part? I have a butcher block table drawer. With both ends but nothing in the middle.

Plastic drawer guide

Need replacement for identical wooden side table drawer. Marked "C-81 6" on plastic. Please help have bought several replacements but none work.

Saw your discussion that RONTHOR Drawer Glide Pat. No. 3185530 is no longer available . What could be used to replace it?

So I ordered part # 32-031 and it was too small. I've taken pictures. part # 32-032 seems closer but I am not sure. Can you tell me what will work? I don't mind buying a few different ones to test and see.

No marks. Measures 2.5" wide 1.75 tall and3/8 deep