Viewing all customer Discussions for:

Door & Window

This is on a harvey window I need 2 of the white metal glides and one of the balance receiver. Also do you carry the plastic hoops for the screen

Have a storm window (possibly Anderson) with a broken latch. Top item is the full unbroken part. Bottom pieces show the broken piece and the l-bracket (?) that goes with it. Thank you, Debbi

two windows don't work. trying to find if you would have these parts. I took pictures of window with cranks working.

Hi looking for hopefully just handle however base works but internal hex is also rounding as shown on handle above

Window latch

Would like to know where we can get a replacement window crank handle for Milgard 3510 Casement window; product line #32 - 167 Its a foldable handle with spline of 5/16 Thanks

The number 8 is printed on the metal coil part. It's 1.25 inches wide and about 7/8 inches thick

8 foot sliding patio doorwall (one panel fixed) seal (?) at movable panel is cracked and distorted. Looking for a replacement.We think the etching on the movable panel says PPG Herculite A CGSB12GP1Seal is made to fit in a slot in the bottom sill that is about 1 inch wide and 3/4 inch deep and the ... (cont.)

The logo that looks like a double M is from Milgard. We have them in the United States. You can find the identifier at the very bottom of the glass in the corner. It's stamped with white paint. It's very hard to find. I have a broken handle. I just need a new handle.

Hi, I'm looking for storm door lock that can replace an old Emtek 322 storm door lock. I looked through the lists on your website, and looks like Mortise Lockset comes similar to what I'm looking for, but would it fit? Thank you. Sara

The manufacture may be Weathertite CBA. Found that on the metal separator between the glasses on the window. Hopefully you can see in the photo what looks like A-S in a box on the left and I believe 8963 on the right. On the white casing that you cannot see in the picture is either 1968 or 8961 d ... (cont.)

Looking to replace wheels. There is old glass doors to porch. I don't think I will find a all housing with a wheels, thinking to replace just wheels by self.

Need a new machine screw for the handle/locking mechanism of our 1995 vinyl, sliding glass door. Recently Milgard sent out a tech to repair our slider and accidentally took one of our screws back to Fresno with him. I am having difficulty in finding a replacement and Milgard is not much help, they ... (cont.)

This balance is for a single hung window. the movable vent is 24" wide x 18" high

Hi Looking for 4 pieces. stamp 31 5 length of the metal channel 32 inches. Thanks

I need a new parts for window open and close control by turning a handle. the arm controlled by handle is 12 inch long. handle is located in the middle of the window. Two arm simatric

Top portion of window will not stay closed. We need the parts to fix the upper part of the window. Trying to fix the window so we can pass inspection as we are trying to sell our house. Thank you for your time. Teresa

The pivot is connected with both springs end only at one side. Both springs are hooked at one side of pivot.the other side of pivot is open.Is that is correct?

Hi, I'm looking to replace a set of channel balance and t-lock balance shoes for a sash in my Pella window. My existing channel balance is stamped 30D and from my research here it looks like that may line up with your S795-30 30" Series 795 channel balance. It's 30" long and the window sash weighs ... (cont.)

Please provide me with the information to purchase replacement vent latches. Phot attached. Tab on top has broken off and not shown Width Larger exterior dimension = 6/16" Smaller interior dimension = 1/4 " Height Exterior = 1-3/16" Interior = 7/8" Color = White