Viewing all customer Discussions for:

Door & Window

Hello, looking to replace the following: 6ea Balance 2922 DS-30004898 6ea Balance 2722 - 300004954 4ea Balance 2720 DS-30006241 16ea Guía ES 10011 Sash

This is the plastic cam that rotates and locks the balancer when the sash is tilted.

need the steel coil for both sides

Hello, I need to replace my window balances but cannot identify which ones I need. I know it is 1/2 inch width and 21 inch length. Thank you, Jebbie

Hi, I need 5 replacement tilt lever slides. I can't find them on your site

they are plastic with a spring load to attach to window (Anderson screen)

The code above is for the side-mounted window lift bars on our house windows. Would like to know what the price is for approx. 6-7 of these. also need replacement "clips" as shown in the photo that allow the lift bars to be disengaged from the window frame....need approx. 12 of these. thanks!! ... (cont.)

Good morning. I am trying to replace my window crank handles. As you can see in the picture, the crank has busted out of the casing (I have several of these in the house). Unfortunately, I do not know the manufacturer of the windows as I am the second owner and have no additional information. If ... (cont.)

These patio doors are original to the house built in 1984. No markings on the rollers or the door frame. Please let me know if you can help identifying them.

Please assist with the part I need. This measured 35" and had the marking 3440

OrderNumber: 2132689 ItemReturning: 2 - 9 lbs Series 160 Coil Balancers ReasonForReturning: The pictures show a much bigger inside hole....I need coils that have a ID of 3/4" to fit on support. The ones you sent is only 5/8" will not fit onto support holder. Do you sell 9# coils with a opening that ... (cont.)

Looking for two left hand crank left from looking out double casement. hand cranks for Hurd casement windows 1988 cranks only just the section only in picture 07900 Wright. The picture is the of the right. Thanks

Need replacement for old window balances. However window jambs only have a round or U shaped opening as shown in photo. It doesn't appear that square channel balances would fit. Perhaps spiral balances may be an option?

Please assist with the correct operator for both left and right side. The outer arm is approx 4 1/2 inches center to center on the holes. The inner arm is about 4 1/2in center of hole to center of gear. The operator itself is about 5.5 inches, the holes about 5 1/8

I need a window pivot pin that is missing from one of my windows . The lencth of the piece is 1.5". there are 2 phillis screws that hold it in place. The "pin" is square shaped as can be seen in the picture of the pin on the opposite side of the windot. It would appear that these pins come in pairs ... (cont.)

I recently had order pivot bars they will not work I am sending pictures of what I need. I can not take window out the ones I ordered would work if the were just straight cut off on the end The ones I ordered are#26-378 they would work without the T at the endRebecca

I need 3 left and 3 right anderson casement window crank assemblies. I do have knobs. the Gears are either completely dislodged or so sloppy the windows dont extend or retract. The pic is one of the ones that need to be replaced. Thanks

24-4 dd5 cmc 87 25 inches Looking to buy at lease 12

Need to replace both sides. String broke on right side window. Had to raise, won't stay in track,won't stay open.

Hello, I would appreciate some help identifying this part. The spline looks to be 11/32 and matches some of your handles however some of the other measurements are different. The total length of the handle is 4 5/8. The set screw is what contacts the spline and holds everything in place.Hopefully ... (cont.)