Viewing all customer Discussions for:

Door & Window

Dear Sir or Madam, one of my pivot bars is broken. Do you think 26-446 will replace it? Are you sure the measurement on your picture is right when it says 1 5/16"? My pivot bar looks very similar to yours but measures 1 7/8". Will Swisco ship to Germany or will I have to provide an US-Address?Thanks ... (cont.)

Please identify sash hardware

Hello, please help us identify the correct size pile weatherstripping replacement for our vinyl sliding doors and windows. They were manufactured by Superior Engineered Products and installed in 2006. Our doors are Series 9100 Dual Glazed French Style Sliding Patio Door. They are no longer in bussi ... (cont.)

I think I need the guts out of part no. 83-123 interior screen door handle. My handle is just like the one that is used in a u-tube how to designed for replacing the latch. It is 6 inches long and I have the latch but no guts in the handle. Thanks

Can you suggest a replacement for this triple track storm window sash panel?

Hi. We have two missing window balancers for a pull up Insulate window. Size is 34.5x 34.5. Do you sale balancers we can use? thank you.

Pulley weight system on Peachtree 31.25 inch square windows double hung, non tilting approved 30 years old. Do you have replacement parts?

Appears to have fractured off at the drive ? or gear?end Can I buy the arm by itself or must I replace the assembly? Jeld Wen casement hinge left ( handle left) opens right

This is the balance from the first of 3 window banks. The numbers stamped on the metal channel differs but otherwise they appear to have the same dimensions - 13 5/8" long, 9/16" wide. The top and shoe appear to match Series 835.The spring length differs but I assume that is due to wear.The window p ... (cont.)

I require some repair parts for Alcan hinge windowsTop latch x2Pivot hinge x4Window lift handle & hardware x10Any insight on these parts?Can they be ordered?Specifically the pivot pieces.

The parts to made are 5/8 in longer than the sample , I do not know if the will work. Hope t r hem this weekend. Neil

I need help finding a replacement handle the screws are 7 7/8s on center. please help

I have attached the pics requested they are 30" I will also need the clips and there is a broken plastic piece that I think I will need as well. Thank In advance

My roller has stopped rolling. Id like to replace it. Id also like to replace the bottom of the channel it rolls in.

What is needed to install a 70-208 screen latch set peachtree??? Your website says a related item is the 33-084. This #4 3/8 wood screw is to be used to connect the plastic screen latch to the aluminum frame? Have you actually tried this? What size rivet would work? Also I need the guide pin that ... (cont.)

The attached photo shows an existing 33" balance (1/2"S x 5/8"d x 33L) that needs replacing for an approximate 15-20lb Certainteed slim line vinyl window approximately 13 years old. I also need a dozen stops (shown in photo "broken stop" and the far right piece in the "spring stop" photo. ... (cont.)

Hi, I have lost both the right and left tilt latches for the lower window pictured. The upper window does have the latches and can be seen in the pic. The existing latches measure 1 1/8in wide. Please help identify- i need both the left and right tilt latch for lower window. Thank you ... (cont.)

Hello, I need to replace Channel Balances for 5 windows in my home. I have attached photos and measurements, as instructed by your website. Window #1: Photos 1-5 attached. The measurements are as follows: Ends of Balance: Length 1-6/18"; Width: 15/16"; Height: 1"; Stamps or Markings: 23 5 RL; ... (cont.)

Hi, I am looking for a replacement for the operator portion of a very old Truth window. I believe it was installed in the 80's and the operator looks to be stripped now. I have added some pictures of the operator unit with some numbers I found on the parts. Two of the entire unit installed and un ... (cont.)

I need two of these. The stamp says 84 IN CALDWELL. Do you have these parts?