Viewing all customer Discussions for:

Door & Window

The only name I can see on it says, Truth. Is or was that a supplier? Can you confirm what I would need to replace this? I need a right and a left. the reach is 9.5 inchesThank you,Jeff

The stamp reads: 26 5 FQ CALDWELL. We can't seem to find a replacement part that matches. Can we please get some help identifying what we need? Thanks!

Need a replacement Balancer for my Milgard Window. Metal is 21" long, stamp on side notes 20 3 CU CMC 2

Hello, Our sliding doors are approximately 25 years old. We are looking for replacement handles. Picture attached. Measurement appears to be 7 1/2 inches. We are looking for replacement handles for 5 doors. On a side note, my husband was born in Camden...62 years ago :)

I need to replace the channel balances for 3 windows. They measure 13-5/8". stamped on them are B.S.I 13 2

I have 4 different size windows each with its best own size channel balance. They are no tilt windows. I have attached pictures of the parts that were in the windows currently as well as the marking of the manufacturer (it?s on the wrong side so you have to read backwards). I can give dimensions if ... (cont.)

Hi, I think it's called a plunger, the pin which holds the storm window in the track to slide up & down. Do you have those? Sorry, I have no idea who the manufacturer is.

This part holds the tilt window in place. When you pull both clips on both sides of window you can tilt window in to clean. I will also need a couple of springs that hold the window up when the window is open. Thank you, James

I removed the channel balance. It has the number 2765 stamped on it. To confirm before purchase, please advise selecting the 2765 Product Code: S395-28 option is correct. Thanks

This is out of a vinyl sliding door and I don't have a brand name for it. The width is between 13/16" and 7/8" wide. Any help would be appreciated. Tim

7 of nine windows in my house have broken shoes and looking to replace all shoes. Hopefully the plastic is better with new ones the old ones became brittle and broke. Here are the picture of the shoes hope you guys can help.

I want to replace 10x window locks (technically, sweep locks and keepers, I think). See attached three (3) photos of the existing locks and keepers, with a ruler to gauge size. I want to replace the 10x in the color WHITE. Number on back of sweep: 30345. US Pat 3,811,718. Number on back of lock: 40 ... (cont.)

Hello, the window safety latch broke on my CertainTeex window. The window opens horizontally. I believe the part is about 3". What is the replacement part I should buy? Thanks!

This is a small bathroom metal window. Both shoes need to be replaced. The bar that fits into the shoe doesn?t have a screw attaching it to the bottom window. so I need the screw. The screw has a square tool fitting in its head. There is a piece of metal in the picture that I don?t know it?s purpose ... (cont.)

I need a replacement for Hurd Double Hung upper window lower sash seal. This seal is kerf mounted ... but instead of single circle bulb, it looks like a figure 8. I think it may just be a crushed circle bulb. It is in upper window but slides against lower window.

I need two sets of the pivot bar shown in the photos

Cannot find storm door brand. Overall door is in good shape. Would like to find replacement handle and lock set. Thank you.

See attached photos from a Viking Non-Tilt Window. Please recommend correct replacement including top and bottom fittings.Thanks,BobMetal channel is 26.75" long. Window weights 18 lb.

Need a replacement balance for an old all-wood Anderson double hung window. I called a local window shop and they identified the window model as 3046. Visible glass size of each pane is 24? H x 32-1/2? W. They identified the part # as 162604, although I don?t see tha5 number anywhere on the exist ... (cont.)

Hi again, Looking for the attached glazing bead. Thanks, Erik