Viewing all customer Discussions for:

Door & Window

I'm trying to find a replacement hinge plate for a mepla 365.290 54/00 hinge. Please see the photos.

Please confirm that I have correctly identified 19-005 & 15-001 before I order 2720 & 2730 replacements 28? series 395. Only other marking I can find is BSI next to LA. Thanks, George

I think my sash guide is close to your 18-015. If not, please let me know. My concern is the side view. I am not sure if it will fit into my windows. I am wondering if I can get a sample before I buy 30+ pieces?

sash control inc.1963 {out side handle} 1060-1943 ------- on inside handle screw holes on inside handle measure 3-15/16

Good Afternoon, It appears that the right side tilt sash pivot pin may be missing on my window. It is a US Window factory: Series: Double Hung Window, Type: VSDH, Code: USW - K- 4. The shoe looks like it is intact in the photo. Can you help with this? It looks like if the part is available, it ... (cont.)

Hi, I am looking for a replacement window balance. The metal spring is broken. The windows has a balance on each side. There is no manufacturer label visible. it only has on the upper plastic part an imprint 1:1. Let me know if you have an idea what part this might be. I have two windows that need t ... (cont.)

There is a cylinder that had plastic coating on it and the plastic wore off. So now the arm falls out of the track. I don't know what exactly I need. Maybe there is a rubber that can be put on the cylinder. That would be the best solution but I don?t know if that is possible?

I need the channel balance for a stanek double hung, tilt in window. I have attached the pics. Thanks, Chuck

Not exactly sure what this part is called. It is found at the base of the bottom pane of a double hung window and fits into the plastic piece in the window track that helps pull the window up and down. This one snapped in half. Need a replacement and I cannot find the name of the manufacturer any ... (cont.)

These are the sliding locks for Acan windows that allow you to tilt the window out for cleaning. As you can see, the top piece that extends out into the window frame to hold it in place is broken.

What is the difference between 84-074 and 84-074B?

Do you sell replacements for these window screen clips? Thanks, Jay

The photo attached is the bracket fixed in the bottom of the window and attaches to the sliding shoe in the window frame. It is 2-1/2" long X 5/16" X 3/16"

Window mfg window depot Clifton NJ. ( out of biz) Right hand tilt latch. 2 1/2 inch in length and 3/4" wide. Plastic tip snapped off and cannot hold window on track when opened. I assume to replace I just pry off the broken one and insert replacement. No screws appear to be holding it in place. ... (cont.)

Hello, I need 4 of these to replace broken ones. They measure 31" in length and are 1/2" wide. They are stamped 3030. They are non-tilt wilndows for the 80's. I believe Ryan was out builder.

Hello, I have a Marvin double hung window which one of the channel balance broke. I captured the numbers on the Channel balance with the attached picture (368 56 p8). What channel balance should I purchase to replace it. Thank you

I would like to replace this door handle with a keyed door handle. What are my options for doing this since this is a 3" hole set? Can I just use this handle and install a seperate lock somewhere else in the frame?

Can these be used on retractable screens

Hi I'm need of ends for the 15 inch balancer's I'm going to order, (15" Series 385 Channel Balance S385-15). I need 4 top parts and 4 bottom parts. I also need ends for two 26 1/2 inch balancer's but don't see them, do you carry them as well the ends also? The first few photos are the ends for the 1 ... (cont.)

Need 4 sets of these rollers. (8 qty total wheels for four windows)