Viewing all customer Discussions for:

Door & Window

I am looking for 2 of these parts for my screens. The windows were sold by Certainteed but manufactured by Vinwinco. I hope you will be able to help me. If not do you have any other suggestions. Thank you, Janice

Looking for a replacement of this part for louver windows for an enclosed porch. Two hexagonal rods are inserted into the sides, then gears inside turn the rods in opposite directions to move the windows along the track. Gears have been worn down through the years (installed in 1960s ish). No idea o ... (cont.)

Need to replace this lock.

I need to replace a broken top roller. The doors are 14 years old. I'll also need directions on how to remove the broken roller roller, as well as installing the new part. Thank you,

I can see an imprint of what looks like AG 41A In the inside of hinge. Also can see ZA35°

I need to replace two balancers and two shoes on a window. The existing balancers are 42 inches long and 3/8 of an inch in diameter with a green tip. The sash weighs 40 pounds. Each shoe measures 1-7/8" long by 7/8" wide by 7/16" thick in its thickest portion. Inside the shoe is the no ... (cont.)

Looking to identify replacement operator and lock hardware (both LH and RH). RH operator has backside stamps including "RH" and "40056". Lock has "30386" on backside. Lock and operator both have "TRUTH" stamps. Looking for both LH and RH replacements of both lock and operator.

I have a window with a truth entry guard operator. It looks like the 39-032, but the short arm has a step up. Do you sell one like that? The 39-032 appears to have a step down.

Hello, There's not much left of the sticker on this window. As close as I can tell, the sticker. I believe it says AAMA certification program C-R30-36x72/C-R40-33x62/JW-18. I hope this is enough info. Any help would be appreciated, Thanks. Jason

Stripped hardware Unable to open or close with ease identifying numbers 140549764 1993845000H Unable to see the brand Thank you in advance for your help

This part is above the window, but I do not know what model it is and I can not find an identical one

the stamp says 27 9 KR Caldwell.

We are Locksmiths in Florida, and just when I thought I had seen it all... The Mortise looks very much like your model: 82-229, but I can't find pulls that look, or are spaced alike? (Pulls on Both Sides. No Key Lock) This is a very nice Condo Assn in Central Florida, but not much main ... (cont.)

The hook no longer fully extends into the frame catch, so that patio door cannot be fully secured. I am unable to tell what the model number of this vinyl sliding patio door is. I see "NAMI" as the possible manufacturer, but that is all I can tell from the information on the door. There are a lot of ... (cont.)

Bifold closet door upper roller with bracket

Weep hole size: 32mm x 3.5 mm (metric) 1.259? x .1378? (Inches decimal) 1 17/64? x 9/64? (Inches fraction) Attached is a picture with exact measurements of the existing weep hole - please use this for size references as it contains all details of every part of the weep hole cover with flapLas Vegas ... (cont.)

I have American Windows Miami brand windows circa 1994. One of them has a broken set of balances marked 24D. I didn't find an exact match. Sash measures 50"x25", aluminum, single glass (15-20 lbs maybe?). The shoe looks like your 15-004 and the top like your 19-042 because it is connected to the top ... (cont.)

trying to find this roller. PPG Herculite K, Tempered Safety Glass, ANSIZ-97 1-1984 1/8 - U, SGCC-1110 4013786

I ordered part 23-043 as it appeared to match the broken part, based on measurements I took and compared before I ordered. Both parts appear nearly identical on comparison when I received them. However, when I attempted to install the new part, I discovered that it is slightly wider in one place t ... (cont.)

Balance spring