Viewing all customer Discussions for:

Door & Window

Hi I am searching for the attached part for my window. The part has cracked and thus has to be replaced. An exact match would be wonderful, if not then please suggest the best alternative. Also not looking for anything too expensive. thanks! Swami

has spring; 22 inch; has 2120G B.S.I. stamped on it

Hello! I have seen several queries about the Series 870 patio door mechanism, presumably an old Philips door, originally marketed for manufactured homes. As far as I can tell, my question is unique- which is, I am looking for the latch/lock plate that goes in the door jamb area. A while ago, I purch ... (cont.)

I need to replace several broken pivot shoes from single hung Patriot windows. The windows are original in a house built during 1998. No markings or numbers are obvious and since there is no cut out, I can't remove the shoes until I order the jamb spreaders. The pivot shoe is 9/16" thick and 1-1/ ... (cont.)

Existing door roller/part: 972459 needs to be replaced. Extensive search has been conducted with negative results. It appears your part 81-087 is a close replacement. Are you able to cross reference my existing part to perhaps match one of yours. John

We moved into house last month with six folding white crank handles missing from Uniframe windows. Previous owner left no window or warranty info. We have no Uniframe dealer in Fargo ND. Can you help me with part, cost and replacement?

I have a non-tilt window that I would like to replace the balances on. The balance is 15" long and 5/8" wide. The number on it says 14 5 LO CALDWELL. Which part number do I need? Thanks!

Hi I sent a question a few days ago and no one responded...I need to know what sash balance to buy.. Inscribed on the sash balance J17 5423 685 11600-17 Thank you

Hi, I am looking to replace the window balances for my vinyl window. Can you identify which balance I need to order from the picture attached? Thank you.

Hello, I have Qty 2 doors that I want to replace the handles- one left and one right. Am I able to get two locks with the same key? Canadian Patent No 919213. 1977 or 73 I can't tell Pat No. 3596954 Are these still available? If so, what would the price be and how much for shipping? Th ... (cont.)

Hi im looking for the replacement for this part in the photos. The stamp says 29 9 CX CMC 7. The string on mine broke. Thanks!

Thank you in advance for your help! I want to replace the coil balances here for what I believe is a "sideload" system, but I'm unsure of what lb springs I need. In the picture, I think there is a six stamped faintly into the end of the spring, but I'm not sure if it might be a 9 (and I'm just ... (cont.)

Dear Sir, Attached are two pics. The first is of a broken shoe. The second is of a shoe that I believe is not broken. Can you identify what I need to replace the broken part ? I need two shoes, one for the left and one for the right hand side of the same window. I also need to know how ... (cont.)

Found your part 95-227 door corner don't know if these are the same. Yours has a different stamp #. Mine is 2 9/16" tall, 3 1/4" long, 13/32" thick. Wheel has no #. Wheel case is 11/32" thick, 1" tall, 1 3/4" long. Wheel is 1 1/8" at widest. Possibly your 84-096

My roller looks like 81-083, and it has the same measurements. However, the part where the screw attaches it to the door, does not have the offset, but is straight up (although it is slightly bent in the picture). Will that make a difference? Thanks! Dave

Marvin Window - 1984 The crank has number 2081 on one of the legs

Hi, I need tilt shoes like the picture. I tried 15-046 but they won't work with my pivot bar.

This is a follow up pic to a pic I sent a few minutes ago. The reference # this goes with is D90774. This pic shows an insignia/maker initials on the handle. It' looks like NW or WN? Thank you

We have two casement windows in a bay window. Both cranks are broken. One handle is striped and the other is striped and has fallen out of the window. Do you have replacement mechanisms that fit these windows? Also notice both have been kept in place with foam. Do you have a solution for attachme ... (cont.)

My sliding window was installed in 1997. The rooler is 1/4" in width to fit into the window channel. The casement and wheel of the roller is 6/16" in height. The casement itself is 1/4". The length doesn't matter, but it is 3/4". It seems after a few minutes on your website that product coe 87-0 ... (cont.)