Viewing all customer Discussions for:

Door & Window

Are standard sliding doors Less than 1 1/8 thick? Measuring my door with digital calipers, I get 1.172" thick, just shy of 1 3/16". I picked up a big box store replacement and it barely fit (needed longer screws), key lock doesn't contact, and striker mechanism is so flimsy it bends when lock ... (cont.)

I need to purchase a replacement channel balance for a Milgard window. It's a 24" long 1/2" channel, and pictures of the ends are attached. Stamped on the channel is "23 9 KR Caldwell". I have determined that I need the S380-24. According to my scale, the sash weight is 28 lbs. Is that close enough, ... (cont.)

Hello, I'm replacing the plastic glazing on the windows of an older house. the old glazing is so brittle that it just breaks apart. I've attached a couple of photos of the old stuff. It's hard to get a good cross-section as it just breaks apart when I try to cut a clean cross-section. The face that ... (cont.)

The following is a warranty number on the storm door: 043003906100374. Attached is a photo of the handle I'm looking to replace.

Looking for single replacement part

I just ordered eight of your S500-30. I can't find a bracket to match the original spiral bracket. What do you recommend?

I have a Simonton double hung 5600 window that needs a couple of new vent latches I figure I will get a few replacements for later of course. The part that I have in me hand looks to be 2" long (including what is left of the part that hold it in) by 1/4 " thick the part that goes in the window with ... (cont.)

There are a total of 8 spiral balances that are broken. I'm not sure they are the proper weight support or not.

picture of my sliding door key-less lock so you can help me with a keyed one. Phil

77008 is stamped inside of latch receiver Need replacement lock

need to find replacement corners

last year I bought 2 acorn door rollers from swissco item 81-030. These have 2 roller wheels each. My doors only use 1 roller wheel. Do you have the right roller for my doors.

Hi I need the universal joint for a pole ring for some Anderson awning windows. The house is from the mid 1980's. I hoped the 11/32 39-336 would work but it's inside diameter is to small. Do you sell something that will fit the post on the windows I have. Need to stand on floor and use a pole to op ... (cont.)

Hi I need coil balances that look exactly like your S160 1/2" coil balance except that it has smaller inner/outer diameter, i.e. your S160 is too large. The markings on my coil balance are: #3.5, 33", PAT52320 and it is 1/2" wide. Do you have such coil? Robert

Hello, I need new channel balances for one window. The stamp on the broken one is B6-26-4 IB5 CMC 45 and on another similar window is 26-4 Caldwell HM. The window is a vinyl Alpine, single hung, Thermopane, nominal dimensions 4' X 5'. By your website I think I need a 27" Series 385 2670 C ... (cont.)

Hi I'd like to get a replacement of cold swell door registraion #10219845450048 as this product is no longer available. Please advise. Thank You!!!

Hi there, It's winter in Australia and my house is freezing because we don't seem to have covers on our weep holes! Do you think this will make the house much warmer. My family don't seem to think so. But I am hopeful! Do you post to Australia and how much would that cost? My have Boral 2001 windows ... (cont.)

I need some channel balances for my no-tilt windows. What if the length of the item, from end of metal to end of metal does not measure out to a whole number, do I round up or down? I have attached photos of all of the balances I need to replace. The picture with 3 balances are all 31" in lengt ... (cont.)

I need 2 of these to hold the window into the side springs at the bottom of the window.

Sliding door in residential high rise of. 9 stories Information on door as follows: Traco View Safe Tempered Glass ANSI Z97.1 - 1984 16 CFR 1201 1 (or I) ?? SGCC - 2489 3/16 U