Viewing all customer Discussions for:

Door & Window

Hello, I need to replace my Spiral Balancer on a window. It is a 25 inch by 5/8 inch, but the tip is white. Which balancer that you stock would be the best match? Thanks.

where can i find flat plastic spine also can pet screen be used

This photo is an aluminum key corner stamped with the code of C404 for a new screen. It goes in several handmade window screens using a wide aluminum rail measuring 3/8 x 5/8 or 7/8 overall. I have not been able to locate a manufacturer nor source for this item. I

Got anything like this one? If I could just get close, I could just replace both sides and drill my own holes and mount. the old one is 2 1/8" long and 3/4" wide. I forgot to pay attention to the thickness before I left the job, but I think they are around 3/8-1/2" thick.

I wish you have a comparison matrix or something to help us non-professional folks see the difference between all your parts! My part is 21" long. Thanks -Ed

I am wondering which channel balance I need. There is the number "2830" on the side. Thank you! Brittany

Hi, we have windows from Pacific Windows. There is a marking on the current balancer, and I set an image with it: 36 4BS1, or something to that effect. I measured our current balancer using your guidelines and they are 37 inches long and 1/2 inch thick. After looking at your site, I thought th ... (cont.)

Door Series 2000/930. The numbers on the hardware are too corroded to read. Hopefully you can help. There are not holes to attach a handle to the door, but a rectangular cut in the aluminum measuring approx. 5/8" X 67/8". The hardware fit into this groove and attached to the outside groove plate ... (cont.)

Unfortunately, this Pozzi window was purchased in 1987 and recently no longer opens, so hope to replace the opener as it is over my kitchen sink. I do have the faded receipt: line #1, part #APG14ZZ3845A002. Other info.: cas prm 143838 45-Bay one lite.. LSR no grille 4 9/16 jamb. The above might ... (cont.)

I am rebuilding screens for Jeld-Wen Norco windows and need these spacers that snap into the bottom of the screen frame to raise it in the window frame opening.

I need sash cams as in the picture and photos. I cannot find identical part in your site. I am also attaching a photo of the top guide for your reference.

what colors does this part come in?

I'm sorry, I cannot identify the maker of the door. The door is installed on a Trojan Houseboat (1973). I'm assuming it to be original equipment. I already removed both rollers before accessing your site. I would be interested in replacing with a roller you would recommend. Thank you for your cons ... (cont.)

Attached photos are from a Malta, double hung, vinyl, tilt window. In four of my windows, the pivot shoes have broken/fallen apart. Please help identify the part and suggest a replacement. My Malta windows were produced in Feb 1999. Jamb is plastic and channel balance dimensions are 1/2" x 1/2" T ... (cont.)

Thank you for looking into this. I cannot find the window manufacturer. Both pivot bars snapped off on my window. I have included a photo of an installed pivot bar, the broken one in the sash, and one broken pivot bar which has been removed. Any help would be appreciated!

Latch for storm door

No number found. Only a small screw

Great site for getting sliding glass door parts but need last pc. Note top pic in second photo. Ty. Jennifer

Hi, have an M&I double Hung window mo0del 380DH series and the right hand (as you face window inside) has broken. You can see by the photo. The other has the warranty and serial number: 380DH series double hung window Warranty 2081481.3 380 H-R25-47x73 AAMA/MWWDH101/1.5.2.97. Looking for one two ... (cont.)

stamp says "26 5(BSI) PC" this is a non-tilting window