Viewing all customer Discussions for:

Door & Window

see the picture that the while shell is 28" x 9/16", with tip measured about 29", which replacement is the right one? I may need over 12 pieces.

I'm am looking for two window balances and a pivot shoe for a Bonneville window. The balance is a Unique 29-D-40, it is 30" long 19/16 wide and 17/32 deep. The sash weighs about 23lbs. I believe I need a S770-30 with a 30-D option, however my balance has the heavy duty pointed hook 62-105, so I woul ... (cont.)

do the 88-013 and 88-014 come in a set or are they purchased separately

I need 2 crank window parts. The model # stamped on it is C-9400-1A. It is 9" from the screw at the end of to circular center hole. Do you have them by another model #.? They are about 15-20 years old and probably Anderson. Thank you.

Hello, i have a sash that weight 40Ib, the balance is 34", 3/8 thick the color of the tip is green, the color of the pivot lock shoe with a green cam. looking at your website, Q&A i realize that the green tip balance, will not support this weight, am i correct? and what is the solution. by the w ... (cont.)

I have a house that was built around 1960 with a 4-section patio door spanning 20'. The 2 moving sections haven't really worked well since I bought it about 3 years ago. I took one of the doors off and saw that the small gears of the aluminum ratcheting mechanism are worn out, preventing me from adj ... (cont.)

I am looking for replacement arm operators or cranks for my old Weathervane wood casement windows. These are from the late 80's. I am hoping that you have some cranks in the same size and tone that will match the existing hardware. I've attached photos. Please feel free to call me for more inf ... (cont.)

This is a lower sash pin.

Hello, this is a top sash guide from a SunAir window. Can you tell me which part replaces this? I've tried to be as exact as possible on the measurements. Thanks very much, Tony P

28" window balance, #2740, from a SunAir window. What part do I order to replace this? Thanks, Tony

Please see the profile of the snap in glazing in need to fix my existing hail damaged windows. From my estimation they look most like 55-120 or 55-180 except the dimensions are wrong. Also my existing glazing is tan or beige.

Series 311/312 sgd internal lock is broke and need help finding replacement part. Top lock does not operate.

Hi Swisco, I need to replace a couple of counter weight balances on my Anderson windows. The stamped numbers on the tab are very hard to read or get a complete number. They all seem to differ a little bit but they all start with 827. Since I'm ordering 6 counter weights I don't want to order ... (cont.)

I need the part shown in the attached picture.

The over all length is 7 1/16", the width is 3/4", the distance between mounting holes center to center is 6 3/8". Is this still available?

Am looking to replace all my corner keys. The part that slides into the metal is 7/16 width with a depth of 3/8 and the length is 1 inch. The corner is about 7/8 squared with a depth of 7/16. Which corner pieces should I buy? Don't want to buy the wrong ones since I am buying a lot. Thanks for yo ... (cont.)

I need to replace a balance that is stamped "26 4 FT CMC 4". I think I need a 26" 380 series. Does that seem correct? Does the old code tell the weight I need? Thanks, Pete

The window is 45 inches by 32 inches. Upper right of the balance is the number 11600 - 17. Lower left is the number D52 727 136 or D52 7127 136. I can't tell if there is a number 1 after 7 or just a large scratch.

the stamp on the balance I am replacing is 27C USB. Which balance should I order? I just want to make sure I get the correct ones the first time. Thanks

I need two crank base Andersen 7191-33