Viewing all customer Discussions for:

Door & Window

I need need replacement Andersen Balances for the following two: 1. D14 7#27 6 80 111600-2 2. D76 8#31 10-76 111600-2 Thanks -Todd

i need a replacement balance and i cant see the matching part # my balance has stamped E4 9#31 7 84 , which balance do i need thanks

Hi there...Rehabbing a property with 38 of these locks/handles on awning windows. There is no 'turning' or crank mechanism that operates the window. You just unlock this handle and push or pull the window open. I see on your site a cam handle lock, #38-064 & matching lock keeper. Is this the best op ... (cont.)

French sliding doors. Home Depot guy called it "really outdated". Do replacement parts exist?

Can you verify if your top sash guide pair 18-124P is what I need? Hoping those would get a lot of my windows in working order. If I find I also need to replace any channel balances, do you carry one that would work?

Cord broke on channel balance, ordered and received the channel balance but cannot figure out how to remove part at top of window guide where the block and tackle is attached. It is a series 765 channel balance. But cannot find installation instructions anywhere and this window type does not have t ... (cont.)

I was told to send a picture of the rubber that I need to replace on my track. Crestline called it a potato track? My openings are 16 feet and 8 feet.

I need to replace these balances. Any info on ordering these parts?

Customer Care: I need to replace several of these plastic roller brackets from BetterBilt sliding windows in my house built 1994. See attached photos of my roller units, also the lock mechanism as a reference. The windows themselves are in fine condition but the plastic roller brackets are cra ... (cont.)

Window manufacturer is MWD Series 165/175 Pivot lock Shoe Please see attached photo for part identification. Thanks in advance! My dimensions: Height is: 1 61/64

i have a bottom sash window that needs new coils both sides See photo this photo is of the top sash coils which is working Bottom part of the coil has a 5 stamped on it Top part of the coil has a 7 stamped on it both in the same window channel

The metal piece is 25" long by itself. This measurement does not include the base and tip plastic piece. The metal channel balencer is stamped with part number K A2435. It comes from a single hung 54" H 42" W Frame. I also need one for a 54" H 36" W frame. I need 4 for the 42" wide and 2 for ... (cont.)

I have a sash lift that is broken. Pictures are enclosed. I cannot find a person who can repair my window for me. Please verify my part choice - S745-32. The channel is 32 3/16" long and 9/16" wide. I do not know the sash weight. I'm sure I can do the work myself if I get the right parts. I ... (cont.)

I have a casement window at my cabin in Pennsylvania. These matching windows close up against each other, but there's no latch besides the operators, which don't work. Please ID hardware to properly secure the Windows. I'm going to try the 39-020 (021) operator, but what about a latch? Do I n ... (cont.)

I saw a picture on the internet that was from your site. I was able to match up the PAT #'s on the back of the window crank I have but now can't find the part on your website. I don't know what kind of window it is but there are two PAT #'s. PAT 4,083,264 and PAT 4,189,248 There is also a nu ... (cont.)

Window about 30 years old. Numbers 11600-3 390 4#19784. I could send it to you if I had a shipping address. Mark Bolles

Hello, We are in the midst of developing a new slider window. We received some sample rollers from you (Part# 87-058), but we believe the housing we used came from elsewhere. I went to your website and noticed the acorn sliding window 9/16

Hi I need to identify the correct coil for my MI window single hung measures 33" x 64" The coil only has the # 8 stamp. Thank you

This is one of six brackets on the fixed panel of a sliding glass door with the slider in the middle and a fixed panel on either side. this unit is between ten and twelve years old.

Hi, the old coil springs are pretty well rusted away and the plastic push caps are disintagrating. Can you match these up please? I would like about 60 pieces. Best regards Bruce