Viewing all customer Discussions for:

Door & Window

DNS Industries 1400 series lock I am wondering if you carry it

channel balance for acorn single hung non tilt. 1981. 29" not including shoe or top. 3/8" wide.280 stamp on metal. also needs 1 1/4 + inch flat clips to insert in window frame. The number 28C is stamped on channel not 280 as I previously noted. Also BS1 BV is stamped

I have been told that I have the Jordan Companies M21/23/25 series single hung windows and I need a sash balance for them. I do not currently live in this house but need to get it repaired after a couple of windows were flagged on inspection. Would you please assist me in identifying the correct sas ... (cont.)

Here is a picture of the window tilt latch, it is 2-3/8" long and 5/8" wide.

I have Pella casement windows one 609, 6 awning type 618 and the rest are 618 also (but not awning style) is this Pella Pivot Plate Hinge Shoe 39-363 going to be the correct for these windows ??

Same window ... I'm look for these as well. Thanks .

It appears to be some type of a stopper, can't open window, and unable to push back in. It has appeared on two of our windows.

What is the functional difference between your P/N's 55-120 and 55-180 snap-in glazing. I suspect either of these might work for my application, but the horizontal "tail" on mine is 0.360" vs. 1/4"/0.250" (55-180) & 7/16"/0.437" (55-120). Which should I choose? Thanks!

I need 24 of these. Thank you. Jeff

I would appreciate your help confirming the parts I need to repair one broken window coil balance. Please refer to Photos #35 and #36 - these are the side that is NOT broken. Then, refer to photos #34 and #32 - these are photos of the broken coil balance. As you can see, there is one coil up at t ... (cont.)

My customer has double inswinging exterior doors (1-3/4" thick) that exit her 2nd floor bedroom onto a flat roof. The same opening has double outswinging wooden screen doors (1-1/8" thick). The flat roof does not have a rail. She would like to be able to keep the inswinging exterior doors ... (cont.)

I purchased a Larson Tradewinds Storm Door last year and want to change out the lever set to match my entry door hardware. Is there any specifics I need to consider when purchasing a new mortise lever set/?

Need the following latches for a Philips window. I believe the lathes are 3 in by 2 in and the end piece are 2 5/8 by 2 3/4. Let me know if I am in the right ball park.

Hello- I have a home with windows which might be the original from the 60s. They are sliding windows and have NuPrime locks by Seasonall on them. A couple have snapped/broken off and so I need to find replacements. It doesn't need to be exactly the same--something similar would be sufficient. ... (cont.)

11600-2 J51 5#23 11 79

while installing a storm door, i made holes in the wrong places.the handles and mechanism wont stay in place.i have several holes on either side but don't know how start over with the holes uncovered.is there a way to repair the holes so i can start over

I would like to know what part number this would be to replace all 3 parts and get that same color.

We need to replace the channel balances on 9 alum double hung windows, operable tops and bottoms. Windows require 37" or 41", series 60 spring loaded balances. Windows are appx 30 lbs each top or bottom. Is there a jamb liner kit we can purchase to convert either both upper an lower, or only lower t ... (cont.)

Looking for replacement handles for Andersen casement windows installed between 1972-1975. Splines are worn out of existing. Bore is 3/8. Looks like your #39-286, but slightly longer. Inside handle are the numbers 50-C-704 with "62" underneath. Your #39-286 also does not have set screw, whic ... (cont.)