Viewing all customer Discussions for:

Door & Window

I purchased a Larson Tradewinds Storm Door last year and want to change out the lever set to match my entry door hardware. Is there any specifics I need to consider when purchasing a new mortise lever set/?

Need the following latches for a Philips window. I believe the lathes are 3 in by 2 in and the end piece are 2 5/8 by 2 3/4. Let me know if I am in the right ball park.

Hello- I have a home with windows which might be the original from the 60s. They are sliding windows and have NuPrime locks by Seasonall on them. A couple have snapped/broken off and so I need to find replacements. It doesn't need to be exactly the same--something similar would be sufficient. ... (cont.)

11600-2 J51 5#23 11 79

while installing a storm door, i made holes in the wrong places.the handles and mechanism wont stay in place.i have several holes on either side but don't know how start over with the holes uncovered.is there a way to repair the holes so i can start over

I would like to know what part number this would be to replace all 3 parts and get that same color.

We need to replace the channel balances on 9 alum double hung windows, operable tops and bottoms. Windows require 37" or 41", series 60 spring loaded balances. Windows are appx 30 lbs each top or bottom. Is there a jamb liner kit we can purchase to convert either both upper an lower, or only lower t ... (cont.)

Looking for replacement handles for Andersen casement windows installed between 1972-1975. Splines are worn out of existing. Bore is 3/8. Looks like your #39-286, but slightly longer. Inside handle are the numbers 50-C-704 with "62" underneath. Your #39-286 also does not have set screw, whic ... (cont.)

I'm looking for 4 tie bars and 12 tie bar keepers. Do you have the in stock And how much? Thank you for your help.

I am trying to find a "vent latch" replacement part for my windows. The number on the part is marked with "11078 PAT. 4824154" and is for CertainTeed windows.

I'm trying to identify a spring replacement for my window. This is a new discussion. Pics are attached. The measurements are as follows: Length - 29 inches Width - 1/2 inch Stamp says 28 3 Caldwell JM Manufactured probably in 1994. Thanks!!

Hi, My patio door lock is not working. I am attaching the pictures. Please let me know the part I need for locking mechanism. Thanks Rao

I am replacing the whole unit including plastic ends, Can you recommend a replacement unit?

Hello- I need to find a replacement for this window balance, the cord broke. The window brand has what looks like two M's stamped in the handle. The window is white vinyl. Probably from the 1990's window is installed as a replacement window in a 1960's house.

Hello, I was looking at the Patio Sliding Glass Door Roller, Crossly Product Code: 81-126 and I have a few questions. The one I have looks very similar to yours, but there are a few differences. Mine only has one rivet on the opposite side of the wheel versus 2 in the picture. Also, it shows the l ... (cont.)

I need 8 channel balances and 10 clips. Number stamp is 2350

Looking for two Anderson replacement balances only stamped ID # are 11600-17 and number BJ13 5#19 7-87. Looking for 4 balances only stamped ID# are 11600-17 and number P82 12#27 6-87. Please advise what replacement parts I need so I can order parts.

Hi - please tell me which part to order to replace the sash guide as in photos. 18-166 or ???? Thank you!

Below are the pictures I called you about. The egress window says Wright & 07900 on the arm and the operator measures 4" The vertical operator says Truth on the arm of it and the operator is 5". Please reply to let me know you received this and if you have further information for me or if you h ... (cont.)