Viewing all customer Discussions for:

Door & Window

I am sending this email with attached pictures of two windows that are missing vent locks. Window is stamped with Repco IGCC CBA 1994. I am looking to replace four broken vent locks on home windows, please see attached. Your time to this matter is very appreciated. Thank you in advance. ... (cont.)

I need the hardware pictured. It is for a wood casement window. I see no markings on the hardware or the glass. Handle is about 10" long, has four holes in it. There are no gears or sliding tracks

I am looking for the seals that slide in a "T" slot along the edge of the doors. I've attached a picture of the doors and the slot. The doors were made and installed in 1950. The data plate reads Pittsburgh Plate Glass Tubelite doors. Any help would be greatly appreciated.

Hello My sliding door handle has the mortise lock missing. The handle has stamped "Sash Controls Inc 060-1255" on it. I know this company does not exist any more, but I was hoping you would know the right mortise lock to recommend. I do have the handle and the thumb lever just the internal mortise l ... (cont.)

Looking for top sash guides per attached? Preferably in black.

Pivot Shoe Info. Needed , Hector / Linda

Today I tried replacing the original sliding glass door rollers 81-128 purchased from Swisco. I've attached to this email pictures of the correct ones needed for replacement. The number stamped on the roller is #31761. The measurement from screw hole to screw hole is approximately 6 inches. ... (cont.)

I need to get a replacement hardware for my casement window ,the only number I could see in the main unit is 0p05-1505 ... The arms have different # each one (0p05-2017, 0p05-2016, 0p05-2019 and 0p05-2018). Please advise the correct part number to replace this defective part.

Replacement for glass sliding doors

wheels on bottom of patio screen door that can be adjusted by turning a Phillips screw on the corner of the door. I can't figure out how to get to - or remove the wheels. I can see that a spring is missing from the bad wheel.

Cant find the brand name of the window. Do you have that part in stock. It a roller I guess?

Do you have the tabs in these photos for this style of window? The window is 15 to 20 years old. Thank you. Dennis

I have an Acorn sliding door (1996) on which the screen door corners and rollers are shot. Your part number Product Code: 84-026 is the correct dimensions, except the wheel size. Yours is 15/16". My original equipment is 1-1/4". I realize that the smaller wheel will still work. I just wondered if yo ... (cont.)

Need order number for the roller pictured

I have a roto casement lock that I am looking for the screw holes have broken off but this is the general look. Is this something that is still available?

My Andersen sash balances are stamped S14 1027 / 5-88 What is your corresponding replacement? Thanks

Hello regarding hardware for 6 awning windows. Hoping that you can help me identify the part. I am not 100 percent sure but may be a Marvin window. The number on the bottom of the mounting plate reads c-1081-101Thanks Carl

Missing glazing on Andersen Window. Color is Terratone. Glass dimension is 20 9/16 wide x 44 1/16 tall as best I can measure. I have one piece of glazing. See pictures. cross section of glazing is about 3/8" x 3/4". The 3/8" section goes into window and the 3/4" section is visible outside. ... (cont.)

I need to Replace these Pivot Lock Shoes I'm unable to get a good measurement they look like a thick 1/2 inch also the only writing I can find is on the glass of the sash it says ( Owen Corning 12-96 ) plus there is no cut out spots so I'm going to need a pair of jamb spreaders are they sold as a pa ... (cont.)

We ordered and received the 55-109 replacement spline, however we are not able to install it into our door. We have 2 dogs and awhile ago I purchased pet resistant tough screen. This screening does not work with this spline. Do you sell screen that is pet resistant or a different type of spline th ... (cont.)