Viewing all customer Discussions for:

Door & Window

#87-106 What is the overall height of the assembly. Mine is 1/2 inch. Thanks.

During the transition of mail personnel, our temporary mail person would place mail in the area between the screen and the decorative frame. Some days when returning from work there had been no mail or at least I thought. Some weeks later I received a letter stating that I had not cashed a check w ... (cont.)

Windows are approximately 17 years old and wool pile needs replacing. Due to design, top corner needs to be cut in order to access start of channel to slide pile in. My husband took to a local window retailer to look at. is there a trick to this or can we get some type of adhesive and use to atta ... (cont.)

Hello! Trying to determine what replacement part(s) to order from your website. The part is stamped with

Hello, I am in need of some balancers parts for the UPPER sash of 2 windows. The dealer the we purchased the windows from about 20 years ago, said the type that I am needing is no longer available. They directed me to your website. I have attached a picture on the items that are needing replac ... (cont.)

Hello, I need to replace a couple of pivot bars on my windows. My bar almost matches your part 26-241. The only difference seems to be that the screw hole on my bar is at 1.5 inches. I seem to have some room in the window frame to extend the bar into the frame but not quite 1/4 inch. There are no ... (cont.)

This counterbalance is 30 old Anderson wooden windows.I have seen pictures very close to mine but not sure if it is the one I need. Can you help? Thank you, Jeffrey

I just purchased a house with Alcan windows and several are broken. This metal part on the side of the window just pops out. Do you have this part? The window height is 40 inches on this unit. Also, how are these installed? Thanks Jerry

Please advise. It is marked 11600-17 and 927 R 76-7093. Thanks for your help.

I have a windowmaster seriers 620, on the Chanel it is stamped 1430 b61 nd. The label on the tag,states aama/nwwda1g1/is2-97 h-lc25-54x96,2ndlline is H-c30-54x96. The string broke on our and I can not find one to match

I would like to order the following items but wanted to check if they are the right parts to order for my windows. Attached are photos of the old parts for your reference.

Can you please help me find the correct replacement parts for 5 windows. The numbers from the parts are as follows: 2850 BS1 TD (for two windows) 2840 BS1 TD 2430 BS1 RR 3440 BS1 T Do you need the measurements if the part numbers are provided? I am not strong enough to remove the w ... (cont.)

what is the width of the double door lock mortise #82-238. there is no measurement on the photograph. also, what is the measurement of the depth from the screw holes to the out side of the lock? thank you!

i got a storm door(self-storing)from home depot(emco)and the home owner want it to swing in can I do it and if so what do i need

I am looking for replacement screen pins for Weather Shield screens. This house is located three blocks from the ocean, so the metal pins that came with the screens corrode in one season and become inoperable. Is there a replacement pin that is less susceptible to corrosion?

These are photos of a scrap I saved last time I was able to locate what I needed at Home depot who no longer carries it. No luck at Lowe's either. "T" top is 3/16" across, and 5/8" from top of "T" to bottom of strip. Clear silicone. Tried a generic double t top that was longer as well and it rip ... (cont.)

I have Marvin casement windows approximately 15 years old. Will folding handle 39-107FK fit these?

The window is a single hung PGT window 52 X 61 3/8 The Metal on the channel measures 1/2" width / 30" length Nymber stamped on channel is: 29 9 (then smaller letters BS1 RV) Can you please advise the proper channel kit to get to repair this window. Thank you.

Hi, I am trying to identify this Milgard screen door handle. It's mounted on the frame. Piece 1: screen holes distance 3" height 3-9/16" total width 2-9/16" mounting section width 1-5/16" Piece 2: screen holes distance 2-1/2" height 3-9/16" total width 2-9/16" mounting section wi ... (cont.)

The latches are on 20-year-old windows. I need a left and a right latch. They measure 2" by 3/4". One screw on top at the back end. One screw on the side. Thanks in advance for any help you can give me.