Viewing all customer Discussions for:

Door & Window

I have several doors with bad rollers and I need to match them the best as possible. I recently purchased the 81-004 and 81023 rollers from you the 004 was the closest match but still required modification to install. I have attached the existing roller and dimensions. Can you match this better than ... (cont.)

I have bay windows that swing open using hardware marked with Sash Controls, Inc. Dated from the mid 1970

I am replacing a Truth Entrygard window arm operator for a casement window opening out and locking on the right (hinged at the left) where the link arm is just over 3 3/4 inches long. Can you recommend a replacement part, because on your site I only see options longer (4 7/16) and shorter (2 13/16) ... (cont.)

I'm looking for the rollers to fix my door. Thanks

attached is a pic of the casement hardware i'm looking to replace. the windows are 30-40 years old, my best guess. I do not have measurements at this time. need both left and right hand operators Thanks! Tony

Do you have these available. Tab/ wedge that goes on top of a screen.

I could not find the patio door manufacturer or part numbers on the door or rollers. Could you please help me identify these? Measurements are approximately 3"x15/16"x1/2" Thanks.

I see "Stanley" written on the windows' hardware. I'm not certain whether the hardware is a Stanley product or whether it's the entire window. Based on the attached picture I suspect you can help. This plastic safety mechanism is failing on many of our windows (the picture was obviously taken of ... (cont.)

I purchased what I thought was the right part but the original part is larger than the new one. Original part #60-03 (small 5). The width is 2 1/8" 4 3/8" long. In any case I need the correct part and I need to return the 24 that I purchased for the 6 screen doors I need to fix.

We are looking for some of these drawer glide supports. Is something like this still available?

Looking for a replacement tract for crestline patio door.

I spoke with one of your representatives and he thought I had a 39-025. However, when looking on line at that operator, the link inside has a slight crook in it, where as you can see from the pictures below (the 4th picture) ours is straight and is approximately 2 3/8". I just spoke with Tim a ... (cont.)

I need to replace a window balance. Can you help me identify the correct replacement? Please see the attached pictures of each end. The length of the balance is 32" (metal to metal) Please reply with the part number, price, and availability. Thank you! Paul

Good afternoon - the crank assembly in one of my house windows has gone bad. It no longer cranks the window inward. This is a left-side opening window, with part number R30842 stamped on one of the arms. The housing has worn away and cracked, which I assume is part of the problem. The crank arm ... (cont.)

I need 2 channel balances for a single hung no swing/titl window. 1/2 inch channel width 28 inches long.

I have Kolbe windows that are over 20 years old. I have an awning operator that the set washer will not hold in the pinion when attempting to close the window. I assume a new operator is in order and it appears the model 39-348 is the ticket. Do you know if this product will fit a Kolbe window? ... (cont.)

I have Alenco windows that are about 17 years old. Some need new tilt latches. I ordered them from Alenco about 7 years ago, but they no longer do that. They are a 1510 series. Do you need a sample or this enough info. Thanks, Laurie

i need a pivot shoe. i saw on line, 15-045. this looks same as mine, but mine is 2 1/4 high, this one is 2" high. does that make a difference. Also, i probably need the jamb spreader, but it is expensive. any alternative. do you rent them?

Part #40-035 can it fit a door 1&1/2 inches thick? If not, have you a storm door knob for a door that thick?