Viewing all customer Discussions for:

Door & Window

Hi, I believe your Part #40-034 is the part that I need, but I wanted to confirm with my pictures. The handle is from an Anderson screen door. Would please kindly take a look and confirm if 40-034 is the appropriate replacement? Thank you very much for your help! Gary

According with the information that I found on the window, the serial # 051-500001 ... I need to replace the Pivot Lock Shoes.... thanks in advance

This picture is the best I can get of the numbers on this sash balance unit. I can't match the numbers to anything listed on your page. I have many windows of idental measurements and these things are breaking/tearing. I'll need at least 8 units (4 windows worth) to start with. Thanks. Nate ... (cont.)

I believe this is 3/16 by 3/16 wool pile weather striping that I need to replace on 17 window screens about 51 feet. Thanks Steve

Hi I am looking for this Anderson split arm. Sizes of the two sections of the arm are approximately 5" and 3". Showing is the left but I actually need the right. Thanks for your help.

Hello, I am trying to find a replacement Mortise Lock for my older Sliding Glass door. I don't know the brand of door but the lock as CD8B stamped on the inside. From other posts on your site, someone with the same lock code was referred to part # 82-211. This part does not look the same as mine ... (cont.)

The controller seems to be about 4" wide and has a stamped number - 306-36. Another part says "Truth" but this name is not on the part of the controller I can see. Do you carry a replacement part? Thanks! Nelson

I am fixing a customers window. It has triple coil balances. I already ordered the carrier setup, and I can't figure out how to get all three coils attached to the bracket. After research I came across the same question answered on your site. I have given up on using the original setup, and I am goi ... (cont.)

Need roto mounting part DR015-1500 in photo. Can you supply? Time and price?

Hello, I have attached 3 pictures for you to help me identify which one I need. I'd like to order (2) of them right away. If these work then I plan on ordering more of them at different sizes. These are 1/2 inch wide and a hair under 28-inches long. Thanks for your help, Martin

Snap in but has no marks to identify it.

Can you please supply the dimension for the width to make sure it will fit in the assembly of a papaiz 323 lock. You show length and height. The assembly I'm putting it in is a papaiz 323. (their cylinder # is 410/55) Thanks, Ron

I need 40 corner keys this size Can you help?

Top righ and a top left tilt window latch. Windows manufactured by All Side.

I need at least 12 pieces can you locate for me.

The windows in my in-laws home, built 1973, in Wisconsin have the attached mechanisms for opening and closing. The photo of the back view shows the following numbers: RH 40056 3 I'm assuming the "RH" means right handed - is there also a left handed version? Not sure how many of each I nee ... (cont.)

Dear sir, I recently purchase Swisco part # 95-032 (5/16" x 3/4") Straigh cut corner. Unfortunately, it won't fit my screen frame which is 5/16" x 1". May I ask your recommendation for the correct part. Sincerely, Sang

I need to replace plastic clips for a storm window panel. The old clips are one inch in length and 1/8 inch thick although slightly tapered. There is a 1/4 inch right angled section that holds the window in place. Help.

Good morning. My 3 year old has broken our front door handle... off :) The door is a Caradco 4101341. Both handles on both doors need to be replaced! Can you help?

In need several of these small night latches for our windows. The windows are the vinyl glue/seamed type. We had everything replaced when we moved in our house around 2003. The company (Window Wizards) has since closed its doors and I've been trying to source replacement latches. Any help? Than ... (cont.)