Viewing all customer Discussions for:

Door & Window

I need two of these - Do you have this, or something close?

I am looking to replace the tilt balances in a number of windows. Each has a plastic cover over the balance. How do I remove the cover without breaking the channel. Or does the new balance slide inside this cover. I can move the cover a little up and down

Here are the photos. Marking 2730 - 28" long the bottom attachments is the one I cannot ID I can get more photos or info. Thanks for the Help. Terry

I have 2 casement windows that new new hand cranks. the windows are good but the hardware is worn. Please see photos and advise. The width of the crakn is about 4 1/4 " wide. The Corado windows are about 40 years old. Bob

Looking to buy a replacement part for one of my home windows. Attached pic shows the 'carrier' (plastic part that is towards the bottom of the assembly shown in pic...it accepts the center rod on window section that moves up n down) that is cracked. Window is a single hung, double pane, tilt in cl ... (cont.)

completely missing window balances . need to identify proper or similar parts

All the windows in this house are void of guides. some want to fall out of the frames. House was built in the 1960's. Latches say Likit. No other info. Rails are only 3/32" wide or so. Do you have the plastic guides for these windows?

I am unable to find a replacement pivot bar for my Polybau double hung windows. Polybau went out of business and I have 3 broken windows. I am attaching photos. If there is not an exact match available, can I substitute another type just to get it to work? Are there any other options you can reco ... (cont.)

I would like to send you a sample of the part I need.pat 4926524

my spiral balance color is white 5/8 38" should I buy the red or the black. I didn't weight the window.

How do I get the sash crank out of an installed window? I have a crank assembly that is broken and it is not obvious how to get it out without taking the entire window assembly out. Please tell me that is not necessary! Mark

do you guys have this part ? please link me to it.PATENT NO.4.505.6014.521.996PAT. CANADA 1986U.K. PAT.2.135.397

Window is 35 x 31( top and bottom) Pictures attached S8 1031 12 87 or 11609-17. I need the left and right side.

facing out removed right(facing exterior of building) balance but need both

It doesn't have any number can you help identify it? Thanks

I am looking to buy a number of 28" 385 series channel balance. Mines are getting worn out, the top and bottom getting half broken, some pulleys have gouges into it, etc. I replaced a few broken strings with stronger material, but still need new ones. I know the type, the width, the length. Whe ... (cont.)

Hi, I need replacement pins that hold the window screen in the window. It has a 1/2" spring around a 1/8" dia. pin that is approximately 1" long. There is a plastic cap on one end (approximately 3/8" long, with a flange head, on the screen side) and a metal cap (approximately 1/2" long) on th ... (cont.)

We have Atrium metal single hung windows where one of the spring balance has fallen down. The problem is that on EVERY window in the house the previous owners removed that popup latch/catch that allows me to remove the bottom sash to replace or reset the balance. Do you sell these latches or catches ... (cont.)

Openings for screws are 3 1/2 inches apart. Can you help? Writing states Dorwal. Do you have a complete kit, including the locking system?

Dear Swisco Techical Dept. We need to replace 7 sets of 32" & 4 sets of 26" channel balance replacement. It looks to me 390 series ( I am not sure), but the channel width is 9/16" and each side measures 5/8". ( marked 3140 on the channel) I am attaching some broken piece photos. The top ... (cont.)