Viewing all customer Discussions for:

Door & Window

I need helping finding a similar sash pivot pin. I need about 10 of them. Thanks

We need to replace two window stops (if this is the right name). The pictures included will show you what we mean. Thanks.

Hello, We would like to purchase the correct locking doir handle and replacement insulation for our 1977 sliding glass door. Thank you for any help. We're so happy we found your site. Lisa

Please find pictures attached of thumb lock to be replaced. From the top of the thumb plate, picture 1 & 2, it is 3". From screw to screw it is 2 1/2". Numbers on back of thumb plate, see picture are, S2573553 & W2574554. Numbers on lock set are 2573558 & 7700-14, see picture I have ordered ... (cont.)

I am looking for your part 81-270 but with stainless steel rollers

I'm not sure who manufactured the screens in our home. The screens all need re-screened and cleaned (as you can see by the images). All screens have knife latches on each side, and stationary pins at the top which go into holes outside the windows to keep the top of the screens in place. I ha ... (cont.)

Do you have these white sash guides?

I need to replace a handle in my father's bedroom. You have one that looks right - Product Code: 39-358 - but wanted to double-check. Two pictures attached. A tape measure is opened to 9 inches in the picture of the original - in which the window opens from the right side. (Mechanism on left side ... (cont.)

Double hung window has no mfg. markings or stamps. The balance rods are marked Caldwell. Length is one and a half inches and one half inch wide

I need to find another track like the one in the photo. My house was built in 1949 and I am having trouble finding a replacement track locally (Oakland, CA). Do you have anything like this?!

We installed 2 Cole Sewell Model S6500 storm doors for a customer in 2001. Customer says he needs replacement pieces to keep glass in on interior portion of door. He described pieces as 2 white vertical strips on left and right sides of glass. Can you tell me what would be the best way to proceed ... (cont.)

I am looking for an roller assembly for door size SGD-R20-120-82, and the wheel size is 1 1/4. See pic. Attached. Thanks Huan

The lever on my Simonton window lock has snapped right off. I need a replacement part. Can you help me? On the back of the lever that snapped off I see the numbers 30387. Guessing that could help? Thank you. I'd love to hear back from you asap. ~cheryl

Hi, I'm trying to purchase a couple of channel balances for my non-tilt Milgard window. Here's a couple of question: 1) My channel measures 19 5/8 " - so do I choose a 19" or a 20" channel? 2) It has a 19 2 marking on it. Not sure what that means. 3) Any ideas how to figure out t ... (cont.)

Ok, so this is the item (2820) I need but part of my problem also is that the plastic piece on the top corner of the window is broken and needs to be replace as well. So, do you guys sell that piece too?

Is 28 4 Caldwell CM equivalent to your 2840 option? It is 29 inches long.

I believe part #84-139 is the correct roller for my Norco sliding screen door. Can you send me an instruction sheet so I can remove it to confirm.

I have window wizards installed Versailles sectioned security door with clips that have a 3/16 hole but am not sure about the offset size because I am not sure where to measure from. Also which is more durable the plastic or metal clips?

Attached is a photo of my mother's vent latch. Unfortunately, I do not presently have a photo of the part installed as she lives 65 miles away. Also, I could not locate any names or numbers on the part or window. Do you recognize this item and carry any replacement parts?

I have a wood patio sliding door. Want to change rollers. The door was installed late to early 70s. Any help would be appreciated . Thanks Mark