Viewing all customer Discussions for:

Door & Window

My house had Anderson Casement Window Dual Arm Model # 7198-17 installed 33 years ago. The only dual arm that I have located is for Awnings, what is the recommended model for replacement ? The arms are 7 1/4, 3 1/4 and 12 5/8" Respectfully, Abe

Need (2) replacement Truth multi-point sash lock keepers for my casement window. Truth p/n: 31415. Mounting hole-to-hole dimension is approxiamately 2-7/16".

The photo depicts the tab fasteners for energy panels on Marvin Windows. I would like to buy several dozen.

Hi, I have measured that the length of the channel balance is 24”, and the width is 0.5”, the weight code is 2340. It seems that I need S372-24, am I right? I am not sure if my top and shoe match your top 19-004 and shoe 15-031. Thanks for your help. Your website is just awesome! ... (cont.)

On the video, you say to position the locks 3.5 inches above the bottom window. This may be a stupid question, but I want my windows to be able to have an opening of about six inches for ventilation so is it fine to install the locks higher? Or does the product prevent that in some way? Maybe the ... (cont.)

Hello I WORK IN A HOSPITAL IN THE I.C.U WARD AND WE HAVE A SLIDING GLASS DOOR FOUND SOME PAPER WORK FOR IT SAYS IT,S A AMARLITE " METROPOLITAN MARK II " ARCADIA SERIES 800 " OR PITTSBURGH PLATE GLASS CO "PITCO GIANT " CAN YOU ID THIS ROLLER FOR ME THANTS

I have two Caldwell channel balances that I need to replace. They are 30 inches long and have 29 3 EQ CALDWELL stamped on them. They are 1/2" by 9/16"s I am enclosing pics, I hope that you can help me. Also, I will need two of the take out clips (16-002) as they seem to be missing from the sash. ... (cont.)

Good morning. I have an issue getting replacement pins for the screens on my Marvin double hung windows. Last June, I purchased Item #70-009 - but they were too thin and they allowed the screen to move around in the window. In May, I purchased item #70-008 - but the pin head was too l ... (cont.)

what is the difference in the sprial balance charging tool for a tilt window and a non tilt window? I think I may have ordered the non tilt but will need the tilt.

I have an Anderson balance (we built the house in 1977), code in bottom right corner is B24 4P1947 6. Do you have two replacements? Thanks!

Hi....I got my friend Jill to buy the replacement snap-in vinyl glazing you recommended to me...it's here. Thanks. :-) Now, the tough part: I cannot remove the windows I need to reglaze from their frames and, well, I can live with that--what's killing me is the old brittle glazing that I'm trying ... (cont.)

Good Morning, We are getting ready to install the 20-013 on our double hung windows. Should we install ONE lock per window - or two - one on each side? Thank you.

Hi, my house was built in 1956 with lots of awning type windows, being pre-AC Florida. There is no branding on any of the parts. The bolt to bolt distance is 3.840 inches, as measured with a dial caliper. I am attaching several pictures. These have been a bane to the family for over 50 years ... (cont.)

I need a 1/2" wide channel balance, 28 inches long for a non-tilt Atrium window. I need the shoe and top attached. I think the part I need is a Product Code: S380-28. Do you think that is correct? I also need a take out clip and a top sash guide and don't know what parts to get for the ones picture ... (cont.)

I am looking for the same part for my other window. The size of the part is 1inch by 4inch.

I have a mid 1970's Caradco sliding door. The screen door for this assembly has two top mounted nylon, concave rollers. The rollers are 1 inch in diameter, 1/4" thick, with an approximate 1/4" center hole. The rollers are riveted onto an aluminum plate that then mounts to the door via two screws. ... (cont.)

Hello, We need to replace the Kinro tandem rollers on our Fleetwood manufactured home sliding glass door. Can you identify this roller so we can buy the correct ones. Thanks so much!

Could you tell me what is the difference between the 380 and the 385 channel balance ? They look the same to me and I can't tell which one to order. Thank you, Karen

We moved into a home with an OLD storm door. There are no identifying numbers or words. I want to replace the handles with a lock for the inside. It is a surface mount door 1 7/8 inch thick that open out. It doesn't need a key lock on the outside, just a lock on the inside so I can keep the door ope ... (cont.)

This is a locksmith company. We're looking for a lock simular or exactly like this. Ruth