Viewing all customer Discussions for:

Door & Window

Do you carry this? Thanks Jeff

The only number I can find on the existing units is: K10 9#31 5-77 Do you have a replacement for these?

WE NEED 3/4" TO STOP THE AIR WHISTLELING THROUGH THE DOORS. WHAT WAS RECENTLY SENT TO US WAS NOT LONG ENOUGH BRUSHES. THE 58 015 WOULD WORK WITH LONGER BRUSHES IN THE LENGTH OF 3/4". PLEASE LET ME KNOW IF I CAN GET THIS. THANKS MARK

THE DOOR HAS THE NUMBER 3068 ON IT AND IT WAS INSTALLED IN 1998.

Need operator assembly for Builbest window. House was built in 1990. Can you tell me where I can find the part # and it looks like I have to take the bottom of the trim off to get at the operator is that right. Thanks, Charlie

this is for a crank out window that opens from the bottom upward, not from the side

The attached pictures show what we are trying to get, although it is a handle for a left handed window. The writing inside the handle indicates in the first pictures is OP06-1520 the first character is o like open. The only thing I can find online ties it to Roto windows, but I can't seem to locat ... (cont.)

Hello, I am trying to figure out which part I need to order to replace my channel balances. I've provided some photos for your review. It looks like it can be either the Series 351 or 390. Thank you!

Anderson balances with the following numbers: D31 7#27 10-81 11600-2 I need 4 units,please advise if available and cost. Thanks, Phil G

How tall is the button? How tall is the arm? What is the exact measurement between the bottom of the arm and the top of the button?

Looking for replacement snap in window glaze trim. White vinyl....."L"shape.....1/2-or 9/16" on face of window, with slight bevel last edge And 1"to 1 1/16 deep into channel, with2 small parralell ribs deep info channel , toward glass side. Thanks for any guidance toward your replacement parts ... (cont.)

I am seeking help please to find a patio door handle with lock replacement kit (both inside and outside handles) and keeper for the attached photos. The handle/lock is on a 1989 Cobra Sentinal park model. The closed black keeper is 3-1/4 inches long and 3/4 inches wide. The length of the insid ... (cont.)

HouSe was built in 1968 looking to replace a couple of cranks I can't get a picture to post for some reason

on the outside door customer is looking to install a lock on the opposite side of the thumb knob is ther a such lock

Andersen Corporation Bayport, Minn. Above Andersen Brand is 11600R-2 Lower Right Edge is marked: E50 8#37 10 86 If I had to guess, I would guess this is a Andersen Sash Balance 837?

Need to identify part number for replacement lock on Andersen 3 door patio sliding door set -- lock is between middle sliding section and stationary right door. Information etched below Andersen brand is: IGCC 306 CII-82S Here are 2 photos of the lock: photo 1 is the thumb know on the interi ... (cont.)

I am having a difficult time finding the glazing bead for my old Better Bilt windows. I need a couple of pieces and have not had luck locating my specific type. Attached are images for what I have. Can you please help me identify my beading? Thank a bunch!

We are seeking a very long handle (at least 6-10 inches)extender than can open a casement window that is a long reach over 25" kitchen counter top. We think 10" is the max we need and the max we can tolerate from an appearance standpoint. We see your 4" extender; do you have anything longer? ... (cont.)

Need to replace balances on both sides of window.

I have vinyl tilt windows with broken shoes causing the windows to fall dangerously. I removed a spiral balance and shoe to take measurements. The Pivot Locking Shoe 15-046 seems to be the exact measurements needed. However, the spiral balance is 30in. length and 1/2in. diameter. You don't show a 1/ ... (cont.)