Viewing all customer Discussions for:

Door & Window

Hi, would you please help me with getting about 12ea locksets, Its an old Corbin skeleton key type mortise lock, 2-3/4 back set. its only being used as a passage latch. insede the body says 1365 1/2. thanks very much. Jerry

Dual Arm Crank, 16-1/8" Product Code: 39-140 does this come with crank & brackets that push window in & out? in other words all parts that are shown in picture? Jerry

I am trying to find replacements for these sash stops. Thank you! NAC

Need to replace the sash balancer on my Anderson Narrowline Window showing this number: D16 7#27 684. What is the replacement part number for this sash balancer. Thank you

Please confirm part number VGB4920W or correct part number to order vinyl bead. See four attached pictures. Thanks you, Ike

How do know which exact Pivot shoes I need? I need to purchase some so that I can fix my window ASAP.

I need help confirming replacement channels. The channel is 34 inches and 1/2 inch wide The imprint on the channel says "33 5 HO CALDWELL" thanks, David

I have a 3510 Lawson balance and need a replacement set. It"s 36 inches. I"m having problems identifying the top and bottom from photos. Each has wings. It looks very much like 19-007 but 007 size is wrong. Can you help me. Thanks, Mike

Hi, just replaced the rollers on our sliding window, model number is 87-006A. It has a metal housing with a metal concave wheel. Does this type of roller need to be oiled, and if so, what should I use? WD-40? Mineral oil?

I have an old patio door that I need to replace the door handle. The measurements are 3 15/16 long(between the two screws) and 1 1/2 inch thick. I see a Patio sliding glass door handle set for 3-15/16" for 1" thick doors on your website but I am unable to find anything for 1 1/2 inch thick doo ... (cont.)

Hello I wanted to find out how wide the turn clip is part number on your website is 70 – 014 into the description picture it shows the length as 1 1/4" and from the whole 5/8" but not the actual width. Thanks, Jason

I have single hung vinyl tilt windows. I need to find both left and right hand latches that slide into a mortise that has been cut in the top of each lower sash. See pictures below. I am including pictures of a good latch. It is 27/8" long and 3/4" wide. I also need the left side window lock t ... (cont.)

I recently bought a part from you guys it was a turning lever, part # 82-106 I thought that would solve the problem because that was missing. I put that part on and it fit except the hook on the inside won't come out when you turn the lever, I'm assuming there is something missing internally. th ... (cont.)

The coil balance is just under 2-1/2" and I think it's part #15-177. My boss wanted to send the coil in to see how much weight it holds. We’re not sure. It’s 1/2" wide. Also, the pivot bar is shorter than the pivot bar I found on your website. The pivot bar I’m trying to order is 2-11/16" l ... (cont.)

I have Alenco windows, and the metal tip-to-metal tip is 28" long. "2740" is stamped on one end of one side, and "27C" is stamped on one end of the other side. Attached are pictures of the balances. The first 2 are one end of balance-1. The 3rd is the opposite end of balance-1. The last two are of 1 ... (cont.)

I am looking to replace a vinal window snap -In glazing for my window, it was damged due to heat. could you please help me to find out this? the pictures are attached with this. Thanks Mustak

How many cycles will this spring last? ie 2500, 4000, 10000

I need to replace a 11600-17 E46 9#31 8-86 What is the current Part Number ? Thanks Russ

How do I install a 82-055 Acorn Sliding Door Handle Set. I cant get the old lock out and the spring keep popping out of the groves. Are there any videos how to install Thanks Sandy

I bought a house last year and I was wondering if you could help me identify which kind of pivot bar this is, as well as what the white piece the pivot bar is in. I'm missing a couple of these on my windows