Viewing all customer Discussions for:

Door & Window

do you know the tilt latch required for this type of window? Please let me know if you need any additional pictures. Thanks.

Attached are pictures of the sash I need replaced. The sash is in a white plastic sleeve and is flexible. There is an additional nipple (round attachment pin.?) that has rusted off the end of the spiral metal end and is missing from the photo. The window is a fixed window and does not tilt in...I ... (cont.)

I cant seem to find a replacement for my larson storm door handle

HI, Can you please help me figure out which part I need to order. they all look alike.

Hello, I am hopefully in the right place. I need some replacement balancers for my Traco 240 security/impact windows I bought at Home Depot, Miami. I believe the correct parts are discussed on this discussion page. I've changed these before and the plastic ends look right (see attached pics) ... (cont.)

We have a medical office where we installed an handicap opener (automatic opener) for our front door. The contractor that installed the opener had to remove the self closer and re-install it on the outside of the door. There is no "spring" to the closer; it will barely close by itself and has no l ... (cont.)

Is the 26-353 pivot bar designed so as the pin is on center, or is it offset?

I have a Truth/45010 which needs to be replaced as it will no longer lock. Part # 82-040 looks similar, however, I need to order it in white. If you do not have that part # in white,will part # 82-051 also work?

Good Day, I have 2 windows marked as so... * Single Hung window * Series Mark 40/50 Premium Standard * AAMA/NWWDA 101/I.S. 2-97 * H-LC25/35-52x96 * Mfr. Code Kinco, LTD in Jax, FL ...and am in need of ordering channel balances (1/2" wide & 25" in length) for each. I have boiled it down ... (cont.)

I need a replacement balance for a single-hung non-tilt vinyl window. I have attached images of the balance with the stamp and shoes for your ready reference. The length of the metal is 31" and width of channel is 9/16" Thank you for your kind help. Bis

Our house is 6 years old and the majority of the sash mechanisms have failed. How do I identify replacement units? I have included pics from one set of failed units; the others are all of the same brand, although are different lengths and I suspect different spring strengths. UB 28D ... (cont.)

Please help me find this window part - my casement window wont open and close properly - thanks

Looking at your website I believe I need the S380-29 channel. I have hurricane proof windows and they are heavy. The stamp on them is 28F. I was wondering if a 28D would equate to the 2840, would the 28F be two steps up to the 2860? Thank You

I have Caradco windows and I am in the need of a casement sash lock and a casement operator, both are right side. Enclosed you will find the pictures of the parts. Please let me know if you have the requested parts as well as the prices. Thank you very much for your help. Jose

The crank has fallen off and just turns. The part is by TRUTH and says Made in the USA. Pictures attached. Do I need to replace the whole operating mechanism? Thank you.

Hello, I recently purchased a pair of S390-29 that worked great on one window but when I tried it on the other window I noticed that the sash guide was damaged. I need some help trying to identify it.I included some pictures as followed.

My windows use series 700 channel balance. i'm missing both channels for a 20" tall window. my 16" windows uses 15" and my 24" window uses 23" . will a 19" channel be the right size for the 20" window? also my old top and bottom shoe had a "tit" that snapped into hole my new 19-001 and 15-008 need ... (cont.)

I need to replace 14 lock keepers. The painters must have removed them and did not re-install them. They are nowhere to be found. I think that I have identified the correct ones, but I would like your opinion. I think that I need 14 of the Casement window keepers(Product Code: 38-089) that work w ... (cont.)

Can you identify this window balance hardware? (Images Attached) I believe that it is block and tackle style but I don't see a match on your website. Could you possibly recommend a substitute part if you don't carry it? I am also looking for a replacement latch. (Images Attached) Thank you, ... (cont.)

Looking on your website I want to confirm the replacement Roller for our sliding glass door. I would guess this is the old style since the door is at least 12 years old. I see two different kinds on your site and want to understand if there are quality differences. Thanks, Charlie ... (cont.)