Viewing all customer Discussions for:

Door & Window

I need a pair of balances for 21year old Kinco single hung non-tilt window. Your series 351-15 looks like a good fit except my balances are stamped 2440BB and elsewhere B.S.I. Can you supply the correct balances for this window? Pictures are attached.

I have broken Viking window locks that look like the P/N 90-005 with the 2 - 1/4" center-to-center holes. Do you still carry the Viking replacements? I need 10 as they break so easily. thanks for your response, availability and cost.

am trying to identify the existing sash balancers in my double hung andersen windows - about 25 or more years old. There are two numbers stamped into the existing balancers they are 11600-17 and BL4 -10# 31-9-84 I need to replace the sash balancer in several windows and they are all the same ... (cont.)

Need assistance in selecting appropriate hardware. Repairing Durette window(defunct) Shoe bears the following Id. :550CSB. Measures: 1 1\4" wide x 1 1\2" long x 1\2" thick. Please advise. Your help will be greatly appreciated

Great site. Photo shown under "Need help with replacement parts" (Customer questions & Comments) appears to show my existing conditions accurately. My question is with the replacement crank model 39-114L. What material is the crank handle? My existing is metal and looks just like the one shown i ... (cont.)

I am looking for a replacement for this Harcar channel ballance. It has a 9/16ths inch wide, by 5/8ths inch deep, by 20 inch tall channel. Attached are pictures of the front, back, top, bottom, and the stamp. The stamp says 2330AA B.S.I What can I replace it with?

Could you please help me identify the attached window rollers? If you have them I'll need 8 units. Thank you, Marco

I have a 28 in balancer "Unique Balance 27F 12:10:58`

I purchased some 18-166 Top sash guides from you recently and thought my troubles were over but now am not sure. The window is very difficult to raise and I noticed the balancer on the left side pokes out from under the sash. Had a difficult time closing the window and also removing the sash to ... (cont.)

I need some white vinyl glazing beads for what I think is a Crestline vinyl slider window. These are wafer thin and very flexible. The face of the beads measures 21/32" or a strong 5/8". The barb is about a 1/4" wide. Can you help me with this? Thanks, SteveWindowRepairGuy.com One Source Renova ... (cont.)

Need help replacing my latches in my home. I hope the pic helps. Some of your products look close but I cant find an exact match. Any help would be great. Thanks Lance

I am trying to find replacement sliding door roller assemblies for sliding aluminim glass doors now over 40 year old. The Australian Manufacturer (Stegbar) tells me they are no longer available. I found your products on the internet and I think one of them might do the job. I attach a scan of ... (cont.)

Hi, My current window screens are in good condition, but the corners are falling apart. they look like the 95-031. My question is, is there a similar item available that is a 2 piece. I do not want to remove the screen to insert new corners. I could not figure out how to insert 1-piece corner ... (cont.)

I am looking for two Traco cam lock replacements.

Hello. I'm needing to replace 8 pairs of channel balancers. They seem to be series 351 type, with a 22 in. long channel. The number stamped on them is 21 S (with "B.S.I." stamped vertically. ) I'm wondering what strength or weight range I should use. The sliding window pane measures 44 in. x ... (cont.)

I ordered these patio door rollers (2) 81-039 but they were too big vertically and couldn't be adjusted low enough to install on the track. There is 1" of room in the patio door housing where the rollers would install and it's 3/8" space from the track insert to the edge of track housing. I need a r ... (cont.)

Hi, I have a Pella storm door that I bought at Lowes about 5 years ago. Even though they still sell the exact same door, they were not able to locate a new "door handle/Lock mechanism that goes inside the door. Attached, please find a picture of the part I need. Thank you for any help you can giv ... (cont.)

Hello: I need 2 replacement window sash balancers for my small Non-Tilt bathroom window. Attached are the images of the existing damaged balancer... It seems to be 14 Inches long and with a 1/2 inch track. The top looks to be a "19-005" but I am unsure of the bottom & Series.. Please get back ... (cont.)

What part should I order The sash weight box is E29/9#27 885 Thanks Ben

I have two Barber & Ross Windows that the balance springs have broke. I'M more looking for replacement springs. The windows are BRVS72060, 2060, White, Vinyl Singe Hung, 20 7/16 X 34 5/16. The tips are RED. Anyone carry these?