Viewing all customer Discussions for:

Door & Window

Cannot locate this part on your website. Need 20.

We have Soft-Lite Tilt Windows at two places. The metal cams are quite easily broken if they bind in window cleaning, etc. It has been a hassle getting replacements from the dealer (Lifetime Warranty) for the handy person... they prefer a $75 fee for a 15 min job I assume. I've decided it less st ... (cont.)

My top sash guides are breaking as they are 10 years old and plastic. I researched your site and found two possible replacements. The spring on one of my windows is 29 3 nm BSI. It looks like 18-166 is a match and 18-044 is real close. From what I can see, it looks like 18-044 is 1/8 of an inch s ... (cont.)

Want to replace balances and the plastic piece on the top outer edge of the lower sash that catches the balance balances are over all 26" metal box frame is 25" 9/16 x 1/2" I need 10 balances and 10 plastic spacer(?) for the top of lower sash Mike

We have a pretty old storm door with a Storm King brand handle. The spring inside the mechanism apparently popped loose and the handle is no longer being returned to its proper position. Replacement seemed like an easy project, but I did not find any Storm King brand storm door handles at my local ... (cont.)

On your page labeled "Screen and Storm Panel Replacement Hardware", under the sub heading "pins" your picture shows a plastic clip that may be a part that I am looking for. Do you sell these and if so, at what price? Thank you, Sue

Our house was built in the early 1990s and included Masterview windows. We have several large windows that slide open and the small rollers in the bottom of the slider section have deteriorated to the point the windows are sitting on the frame and are now generally unable to slide open. I was able ... (cont.)

I have attached a picture of a corner pivot bar. It measures approximately 2.1/4" at it's longest point. 5/8" wide. 3/16 thick. Could not find in your catalog. Also my pivot shoe is 8/16" X2" X 1 .1/4". I'm wondering if there is any 8/16". may be they run small?? Please advise.

I have leaky CertainTeed awning-style windows when the wind blows strongly. The strike? plates at the top of my windows have rusted/crumbled due to ocean air (see picture). As a result, I think, I've noticed that the seal is not tight along the top-middle edges (both inside and outside) of this awni ... (cont.)

Looking for a lock for my patio Door. Existing hardware is a Sash Control 1963 exterior handle. Would 82-306 work?Does the 82-306 also come with the lock?

looking to match this window balance and top sash guide. it is out of a lawson series 7000 window. the window balance has a marking of 2620 on it. it measures 27" in length.

Does your track cover 1/4" fit over the lip of the 1/2" track or am I needing a 1/2" cover?

I am replacing the broken balancers in my windows. They look like the 350 series. They are 29 inches long. They have stamped on them ub 26D USB and 28D USB. I was wanting to order the correct one. Thanks Jim +

Hi, I bought a locking handle with a key for my sliding glass door. Product number 82-055K. Please help, the hardware came with no instructions. I have no clue how to install this. There are multiple sets of screws and I don't know where they all go. What are the steps I should take to install ... (cont.)

What is the correct replacement for Andersen Sash Balance 11600-17, also shows B44 #19 4 87? On the back side is stamped 11600-3. Also what I beleive are patent numbers 35455 and 1967 CAN.

My home was built in 1997 and has the original windows - which seem to be good. The tilt latches are breaking though and I can't seem to figure out who made them to order replacements. The etching in the glass looks like it says "CFA Windows 10-96". It looks a lot like your Rollyson 2-5/8" type ... (cont.)

Hi, I finally found a site that may be able to help my window situation. I have vinyl tilt/double-hung windows with the spiral balance and pivot shoes. All of my windows have been broke for some time with the rods from the spiral balance tubes all being popped out of their pivot shoes. So here are ... (cont.)

I need 2 replacement locks for Marvin Trimline Sliding Patio Doors. These were purchased in 1996, before Marvin made changes to their product line. The current lock is a mortise lock, Marvin part #02100960 and jamb strike part #02100961. If possible, I would like to replace it with a multi-point lo ... (cont.)

I have a 12" balance on each side supporting a window sash with a weight of 6.4 lbs. On another set of windows I have a 24" balance on on each side supporting a window sash with a weight of 16.9 lbs. These balances do have a stamp, although one side says 2320, the other side 2330. Shouldn't the ... (cont.)

I have two balances that need replacing. They are stamped "233". They are 1/2" chanel and 24" long After looking at your premade balances It looks like they have a 19-002 top and either a 15-001 or 15-002 shoe. I can't seem to see any difference between the two. My shoe looks similar but just ... (cont.)