Viewing all customer Discussions for:

Lavatory

2008 American coach, Corner shower cylinical doors

I have a Manhattan manufactured glass with metal frame (gold) Whower door (two doors that slide and two panels that are stationary) and I have an issue with one of the doors. I need both the top see the two pictures included each have a place to screw into the door and two wheels and two bottom bra ... (cont.)

Hey,Base is developing cracks. Is it realistic to just replace the base, or is the whole assembly a goner?Thanks,BrianPls don't add my info to any mailing lists.

The shower door sweep as shown above with the drip rail needs to be replaced but since there is no name on either the shower or door we have been unable to find any parts. We are willing to replace both the sweep and drip rail if easier . The actual width needed is 25 3/4 inches . Is there a part th ... (cont.)

The length of the sweep is 30-1/4. The total height of the sweep is 1-1/8. The width of sweep from mounting frame to end of drip is about 5/8.

I have two upper roller assembly that have cracked and broken. It is only on the one door, the other one is fine. I would need 2 rollers.

Do you know where I can get these parts for a Manhattan sliding shower door? The numbers written on them are 48037 and 48036 and 48039 and 48038Ken D

Need a plastic door handle for a Stanley safety mirror

Our house was built in early 1970s and still has the original shower. We plan to remodel the bathroom in a couple of years. In the meantime, I would like to address one problem with the 2-panel sliding shower doors. As the photos show there is an aluminium bottom track with 2 channels. overall width ... (cont.)

We are looking for the wheels and screws.

Cant find this sliders all 4 went bad. Hope for some help thanks

Hi - I have a pivoting shower door with an aluminum piece on the bottom. The piece has a 1/8? slot that goes to a T. The width of the T is about 1/4?. The shower has no metal piece under the door and the gap frkm ahower to door as about 1?. I?m looking at sweep item number 10-321 and think it ... (cont.)

My question is about how the 10-216 locks in the bottom door guide? When I raise my door up to free the roller the 10-216 does not let go. If I set the door down on the track it did not let go. Thus when I tried to remove the door I broke one of my 10-216's. Do you have any instructions, pictures et ... (cont.)

where are the screw holes located?id there one in the center?

Need to replace a T-shaped shower door sweep. Dimensions are: 18" x 1/2" x 3/32". This is on an 18"door mounted on a 36"wide Aqua Glass shower that was installed in 1987. There are no identifying labels on the shower door.

This is a side mounted sliding door guide badly discolored. The channel is 1-1/2? wide. I need 4 of them. Hopefully they will be clear in color. Thank you so much. Mike Ingram

Looking for this part that attaches to the bathroom shower sliding glass door.

Hi,I purchased this and cut it to the required dimensions to make it fit my old shower door. But now the door does not close and gets stuck mid-way.To confirm that the rubber strip is the issue, I removed it and installed only the aluminum sweep and the door closes perfectly. So I cut the rubber str ... (cont.)

I would very much appreciate if you could help me find the seal for my shower door. One pieces goes at the bottom of the glass door and the other is on the edge of the stationary glass partition where the door closes on it.Attached please find 2 photos of the vertical seal showing the profile of i ... (cont.)

The shower door is not closing properly at the top. The plastic sweep on the bottom of the door is worn away. The seal around the glass door is deteriorating. The door is 67 3/4 x 23 3/4.So basically looking for parts to make the door functional again.Who is the manufacture of the shower surround? ... (cont.)